kN 2. A simply supported beam a W410 x 114 carries a uniform load of 12- and a concentrated load of P at its midspan. The beam has a span of 10m and it is assumed to be laterally unsupported. Fy=250MPa. Find the safe value of P. Properties of W410 x 114 A 14600mm² d = 420mm bf = 261mm tf = 19.33mm Sy = 439x x10³ mm³ ly = 57.2 x106mm4 tw=11.6mm rx = 178mm ry = 62.6mm Sx = 2200x10³ mm³ Ix = 462 x106mmª

kN 2. A simply supported beam a W410 x 114 carries a uniform load of 12- and a concentrated load of P at its midspan. The beam has a span of 10m and it is assumed to be laterally unsupported. Fy=250MPa. Find the safe value of P. Properties of W410 x 114 A 14600mm² d = 420mm bf = 261mm tf = 19.33mm Sy = 439x x10³ mm³ ly = 57.2 x106mm4 tw=11.6mm rx = 178mm ry = 62.6mm Sx = 2200x10³ mm³ Ix = 462 x106mmª

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Analyze the beam shown in the figure below using Kani's method. Draw BMD. 30KN m 1 SPKN 20KN/m Sm. 1.51 21 Gm. I
Ql: Compute the value of Eld at the distance 3m from A for the beam shown below: 1 kN/m M-2 kN-m 3 m 1 m B I m
I need the answer as soon as possible
04. The load Q is gradually increased from zero to 120kN. a) Does failure occur in bars BE and BD? b) Determine the maximum deflection at pointB. a = 0.64m Square Cross-Section 10mm x 10mm 1.7m E A36-Carbon Steel A36-Carbon Steel 2.64 m OD for all pins = 6mm
The simply supported beam consists of a W530 × 66 structural steel wide-flange shape [E = 200 GPa; I = 351 x 10^6mm^4]. Determine (a) the beam deflection at point A. (b) the beam deflection at point C. Assume P = 30 kN, W = 59 kN/m, LAB = 3.2 m, LBC = 3.2 m, LCD = 3.2 m, LDE = 1.6 m.
Use slope-deflection method to compute the bending moments of element ends for the following structures: 7) Use slope -defle ction Ast 4 4 12 t- 2006 Pa I= 100x 16mm" E = 200 GPa %3D I= 100× 106 mm4 For this question also compute the deflection at Point B.
The simply supported beam consists of a W530 × 66 structural steel wide-flange shape [E = 200 GPa; I = 351 × 106 mm4]. Determine(a) the beam deflection at point A.(b) the beam deflection at point C.Assume P = 44 kN, w = 87 kN/m, LAB = 4.0 m, LBC = 4.0 m, LCD = 4.0 m, LDE = 2.0 m.Answer:vA = mmvC = mm
The 75-lb block has a downward velocity of 2 ft/s when it is 3 ft from the top of the beam. Determine the maximum bending stress in the beam due to the impact, and calculate the maximum deflection of point B. Ew = 1.9(103) ksi.
The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I = 370 x 106 mm*). For the loading shown, determine the beam deflection vc at point C. Assume P = 56 kN, w = 22 kN/m, Lag = Lsc= 2.9 m, Lco = 2.9 m. LAB LBC LCD Answer: Vc= mm.
l8
None
A steel beam is 24 inches tall, has a length, L, of 32ft, and has a yield stress of 36ksi. The simply supported beam supports a single load, P, of 17 kips at its midspan. If the theoretical maximum deflection of this beam is -(PL^3)/(48EI), determine the required moment of inertia such that the actual deflection of the beam will not exceed a value of L/360, and the actual stress will have a factor safety of 1.5 with respect to yielding.