Justify the following statements: The size of program counter is of 13 bits. ii. iii. i. Direct address is of size 7 bits while indirect address is of 8 bits. CALL and GOTO instructions, the size of program memory page is of 2K.

Justify the following statements: The size of program counter is of 13 bits. ii. iii. i. Direct address is of size 7 bits while indirect address is of 8 bits. CALL and GOTO instructions, the size of program memory page is of 2K.

Name: Justify the following statements:i.The size of program counter is of
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: Justify the following statements:i.The size of program counter is of 13 bits.Direct address is of size 7 bits while indirect address is of 8 bits.CALL and GOTO instructions, the size of program memory page is of 2K.ii.iii.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

10.- Consider the following code and pictureLoop1MOVLW 0x32MOVWF REG2DECFSZ REG2,FGOTO LOOP1 If the system clock frequency is aMHz and each machine cycle consumes 4 cycles of it. Calculate the delay time of the LOOP1 loop. Include the execution difference time of the DECFSZ instruction in the last cycle. Select an answerA) 0.6.sB) 6msC)6usD) 60us
Write pseudocode instructions to carry out each of the following computational operations a. Determine the area of a triangle given values for the base b and the height h.
i. Using a flow graphic and an Intel microprocessor, briefly describe how adding two binary integers works. ii. For the flowchart above, create a pseudocode and a code in any easy assembly language. iii. To perform a reduction procedure, follow steps I and ii above.
42. Identify the condition under which the contents of AX would remain unchanged after execution of the instructions that follow. MOV SHL SHR CL, 4 AX, CL AX, CL
4. Consider the following instruction: and $t0, $e5, $3 a. What are the values of the control signals generated by the control unit for the above instruction? RegDst Jump Branch MemRead MemtoReg MemWrite ALUSrc RegWrite
1. Translate the following algorithm to this simple computer's assembly language and then to machine language. (use the columns in a table as shown below) Label Operation Operand Address Machine Code Comments read a read b set c = 0 if a == b set c = a - 7 + (2 * b - 3) else if a == 3 set c = a b + 2 write c
Justify the following statements: i. The size of program counter is of 13 bits. ii. Direct address is of size 7 bits while indirect address is of 8 bits. ii. CALL and GOTO instructions, the size of program memory page is of 2K.
x = 4 and x = 8 **** and 3X is a two digit number, consider memory storage of a 64-bit word stored at memory word 3X in a byte-addressable memory (a) What is the byte address of memory word 3X? (b) What are the byte addresses that memory word 3X spans? (c) Draw the number 0XF1234567890ABCDE stored at word 3X in both big-endian and little-endian machines. Clearly label the byte address corresponding to each data byte value
Q2: Design and draw a diagram for the hardware that implements the following statements. xz+yz : ARAR+BR Where AR and BR are 6 bit registers and x, y, and z are control variables.
Q4: Fill in the blanks: [11 Marks] 1- The execution of instructions stored in main memory is done by 2- Primary storage consists of 3- To increase throughput .... 4- If memory size = 2GB which is equal to.. to............. KB and is equal to .......... and ....are used. MB and is equal Byte. 5-in Random Access, if a write operation to memory location 100 takes 10 ns and if this operation is followed by a read operation to memory location 3000, then the latter operation will take 6- This is to be compared to Sequential Access if access to location 100 takes 500 ns, and if access to next location takes 10 ns, then it is expected that an access to location 205 may take . . ns. ns. ..... 7- The valid bit is included in ............
Which of the following statements is incorrect? - Assembly language gives the programmer complete control over the hardware. - An assembly language is a mnemonic representation of a binary machine language. Each assembly instruction represents a unique machine instruction. - Assembly language can be translated/assembled line by line to machine language in a single pass. - An assembly language is translated into a machine language using an assembler