Q: Design the duct system by using velocity reduction method andof dampering required. Assumedynamic loss coefficient of 0.3 for downstream and 0.5 forbranch and for the elbow. The dynamic lossfind FTPmax and theamountaupstreamtocoefficients for the outlets may be taken as 1.0.1m /s10 m2m3 /s30 m9 m/sFAN30 m45 m10 m1m /s

Jesign the duct syste by using eduction method and find FTP- and the of dampering required. amount Assume a dynamic loss coefficient of 0.3 for downstream and 0.5 for The dynamic loss upstream to branch and for the elbow. coefficients for the outlets may be taken as 1.0. 1m/s 10 m 2m /s 9 m/s 30 m FAN 30 m 45 m 10 m 1mis

Jesign the duct syste by using eduction method and find FTP- and the of dampering required. amount Assume a dynamic loss coefficient of 0.3 for downstream and 0.5 for The dynamic loss upstream to branch and for the elbow. coefficients for the outlets may be taken as 1.0. 1m/s 10 m 2m /s 9 m/s 30 m FAN 30 m 45 m 10 m 1mis

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is transferred from one reservoir to another through centrifugal pump as shown in the figure, The ietion n p from the reservoirs to pump inlet is 12 A. The water vapour pressure is 66 Tbe and atmospherie prosiare is 147 p the available for this piping system. (Density ofr water is 62.24 Thm/ and viscosity is 0.001307Kg/m.a) 3) Z3 Reservoir Z3-Z1 Valve Reservoir
B. Given: Cylinder Diameter = 95 mm Displacement Distance = 110 mm Pressure Ratio = 8.72 P1 = 145 Kpa T1 = 26 Degree Centigrade Mechanical Efficiency = 78% Solve: Suction Volume, Mass Flow Rate, Work Done and Shaft Power N = 1350 RPM
Please solve question hand written
Problem 01 Find the least number of 150 mm diameter pipes required to transmit 170 kW to a machine 3.2 km from the power station, if the efficiency of transmission is to be 90 per cent and f= 0.0075. The feed pressure is 4800 kN/m². Collutate of Pipes required efficiency= Problem 02 A turbine of efficiency 78% is 750 m lower than the supply water source. The pipe supplying the turbine with water is 200 mm in diameter and 4,5 km long. Take f=0,008 and determine the maximum power output that can be expected from the turbine. Problem 03 A pipeline is 1800 m long and 375 mm in diameter, and supply head at inlet is 240 m. A nozzle with an effective diameter of 50 mm is fitted at the discharge end and has a coefficient of velocity of 0,972. If for the pipe is 0,005. (a) The velocity of the jet (b) The discharge (c) The power of the jet C1Reg
Rotameter having a glass float (sp. gr = 4.0) is calibrated to handle a maximum flow of 80gpm of water. Whatis the maximum flow rate of biodiesel (sp. gr = 0.9) can it handle in gpm?
A UMC 50-80 circulator is operating at 1750 RPM. Flow is 50 GPM. Feet of head (friction) is 19 ft. Brake horsepower is 0.40. RPM decreases to 60% of maximum. No other changes occur to the system. What is the new GPM?
A duct system layout is shown in the figure below, it is supplied with air from a central air conditioning unit. The ducts require to be rectangular with a maximum height of 10in due to ceiling limitations. Maximum air duct velocities are: main = 1200fpm; branches = 800 fpm. Determine the sizes of the rectangular ducts and the static pressure at the AHU. Use Velocity reduction method. AHU- AIR HANDLING UNIT (CENTRAL AIRCON)
Explain and Plot the whole process why the pump work arrived in kilowatts(KW) unit.
Solve it correctly please. I