Jack was using sodium dodecyl sulfate at a concentration of 9 mM as the major surfactant in his formulations. For cost reasons, the company decided to switch to decyl sulfate as the major surfactant. What should bè the concentration of the surfactant to achieve the same performance? O 3 mM O 27 mM O 18 mM O 81 mM

Jack was using sodium dodecyl sulfate at a concentration of 9 mM as the major surfactant in his formulations. For cost reasons, the company decided to switch to decyl sulfate as the major surfactant. What should bè the concentration of the surfactant to achieve the same performance? O 3 mM O 27 mM O 18 mM O 81 mM

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter5: Errors In Chemical Analyses

Section: Chapter Questions

Problem 5.10QAP

See similar textbooks

Similar questions

Which of these acts as a buffer in embalming fluids? sodium lauryl sulfate EDTA lanolin calcium
Determine the total hardness of water (ppm CaCO3; MM: 100.09 g/mole) if 100.0mL sample of drinking water required 38.41mL of 4.65 x 10-3 M EDTA for titration. 179 ppm CaCO3 357 ppm CaCO3 452 ppm CaCO3 733 ppm CaCO3
How many liters of softened water, containing a sodium concentration of 4 * 10 ^ - 2 % sodium by mass, have to be consumed to exceed the FDA recommendation ? (Assume a water density of 1g / m * L ) Express your answer using two significant figures.
A student determined the concertration of NaOCI in a commercial bleach sample using the same technique described in section "F" of the Halogens and Their Compounds lab. The student required 18 drops of 0.01M Na25203 to reach the end point. What is the concentration (reported in percentage) of NaOCI in the bleach sample?
Calculate the eq/L of 0.01 M Ca^2+
Calculate final MgCl2 concentration in mM for tube 2 and 3.
An unknown sample containing mixed alkali (NAOH, NaHCO3, or NazCO3) was analyzed using the double flask method. A 250 mg sample was dissolved in 250 mL CO, free water. A 20.0 mL aliquot of this sample required 11.3 mL of 0.009125 M HCI solution to reach the phenolphthalein end point. Another 29.0 mL aliquot of the sample was titrated to the bromocresol green endpoint using 311 mL of the standard acid. What is/are the component/s of the sample? O Cannot be determined O NAHCO3 only O NAOH and Na,CO3 O NazCO3 only O NAHCO, and Na2CO3
An unknown sample containing mixed alkali (NAOH, NaHCO3, or NazCO3) was analyzed using the double flask method. A 250 mg sample was dissolved in 250 mL CO, free water. A 20.0 mL aliquot of this sample required 11.3 mL of 0.009125 M HCI solution to reach the phenolphthalein end point. Another 29.0 mL aliquot of the sample was titrated to the bromocresol green endpoint using 31.1 mL of the standard acid. What is/are the component/s of the sample? O NazCO3 only NaHCO3 only O NAHCO3 and Na>CO3 NaOH and NazCO3 O Cannot be determined
The Kjeldahl method was used to determine the nitrogen content of a protein. A 275 µL aliquot of a 47.0 mg/mL protein solution was digested in boiling sulfuric acid. The solution was made basic and the liberated NH, was collected in 5.00 mL of 0.0512 M HCl. A volume of 7.00 mL of 0.0174 M NaOH was required to react with the excess HCl. Calculate the weight percent of nitrogen in the protein. weight percent: wt% N
Why does the glasswares need to be rinsed with 0.1 M HNO3 prior to use?
A 15.00 mL sample of hard water was titrated with a 0.0150 M EDTA solution. The titration required 26.72 mL of EDTA to reach the end point. What is the total hardness concentration of the water sample in ppm?
A phamacist reconstituted a vial of 750 mg Cefuroxime Sodium Powder for Injection with 6mL of sterile water for injection. The reconstituted solution was dark amber-colored solution. The package insert states that solution colors range from clear to yellow depending on concentration, diluent, and storage conditions. The pharmacist was then hesitant to give the patient the solution due to its unusual dark color. Five portions were taken from a batch of cefuroxime sodium. Prior to testing in the instrument, each part was subjected to one of the following conditions: Conditions Specifications Temperature Portion 1: 8°C ± 2°C Portion 2: 30°C ± 2°C Portion 3: 40°C ± 2°C Light Portion 4: Kept in the dark Portion 5: Exposed to direct sunlight a. Which form of the product – the powder for injection, the reconstituted product, or both – will you subject to the following conditions and why? b. Will you also expose the reference standard of cefuroxime sodium to the same…