Is the 'fit' between the 2 parts shown below a clearance fit or interference fit?

Q: I need some help with this problem. On the drawing below, calculate the virtual sizes for the…

A:

Q: The figure above shows the forces exerted on a block that is sliding on a rough horizontal surface:…

A: Write the equation for the net force. FNet=maF-FR=Wga Here, The applied force is "F". The friction…

Q: the meaning of the graphics below

A: Given: two graphs are shown in graph (a) load is shown on y axis and deformation is shown on x axis.…

Q: Calculate the magnitude of the clockwise couple M required to turn the 44-kg cylinder in the…

A: Find Find the moment M.

Q: 30 B 45° 30° D

A: Part A) Draw the free body diagram at point B. Similarly, draw the FBD at Point D.

Q: 2) If force F1 = 40 kN and F2 = 13 kN, and the couple moment M= 45 kN•m, replace all these applied…

A: as per our guidelines i solved 1st question only

Q: determine the magnitude of the force (Ib) of n e final answer expressed in 3 decimal places.

A: GIVEN: X=13.7ft y=7.7ft

Q: The 800-1b cylinder is supported by three chains as shown. Take d = 1 ft. (Figure 1) Figure < 1 of 1…

A: Here, co-ordinates of points are, A(0,0,-1), B(1cos1350,-1cos1350,0)=B(-0.707,0.707,0)…

Q: If the frictional moment at the pivot O is 7 N-m in the clockwise direction, determine the tensions…

A:

Q: Determine the magnitude of F2 which will cause the reaction Cy at the bearing C to be equal to zero.…

A:

Q: A wide, thin slab of honey is flowing at a constant speed down a plane surface inclined at angle 0.…

A: By the conservation of energy,m/H × g× Lsinθ = 12×mH×VH2VH2=2×g×L×sinθVH2=2×9.81×2×sin 20°VH=3.663…

Q: The part view should.com RANCES be the same CHD APPVD MIG GA as picture. 2- The color is RGB as DWG…

A: Find Draw the given object using the drawing.

Q: Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal…

A:

Q: For H20, determine the specified property at the indicated state. (a) T= 140°C, v= 0.5 m/kg. Find p,…

A: Hello dear As you have posted multiple question at a time  and according to our Policy Iam able to…

Q: Please use the isometric graph paper in my picture to draw it to scale!

A: According o the given data Three orthographic views of the object are given  We need to draw The…

Q: Hi, can you please show me how to solve this problem? Thank you!

A: The objective of this problem is to determine the maximum tensile stress, maximum compressive…

Q: Problem 2–17. Fluid Statics. Pool drains can be dangerous things: There was a tragic case recently…

A: Given : The radius of the ball = R The diameter of drain = D Solution : (a) As the ball is in under…

Q: Construct the three principal views from the given isometric view. The object is symmetrical about…

A: Given: Construct the orthographic projections from given isometric view.

Q: impact with the barrier, and its velocity right after collision are given in each figu ne work done…

A: given:

Q: A centrifugal pump driven by a directly coupled 3 kW motor of 1450 rpm speed, is proposed to be…

A: A device which converts mechanical energy into pressure energy with the help of centrifugal force is…

Q: What to submit? 1. Set up a CFD simulation for the horizontal channel by Ansys Fluent. 2. Define the…

A: DefinitionCFD simulation:CFD simulation is a computer-aided engineering (CAE) technique that…

Q: The pumping unit is used to recover oil. When the walking beam ABC is horizontal, the force acting…

A: Given :-  Fc = 250 lb  ABC weight = 130 lb  C weight = 64 lb    Find :-  Torque M which must be…

Q: th a spring with spring co hitial position ro = 5 m a in meters.

A:

Q: 5-35. The smooth pipe rests against the opening at the points of contact A, B, and C. Determine the…

A:

Q: Hi, the attached image shows a question and its answer but still, I couldn't understand it please…

A: In order to understand the solution given here, first of all understand the phase diagrams provided…

Q: 1) If force F1 = 36 kN and F2 = 26 kN, and the couple mom determine the total moment (in kN•m)…

A: GivenF1=36kNF2=26kNM=65kN-m

Q: Given the two views of a multiview drawing of an object, sketch the missing top view on paper.…

A: Given view  Front and side view  Missing view : top view

Q: a) Write the velocity V and the displacement x of the occupant compartment of the car as a function…

A:

Q: Example 4 (Kinetics: general motion) The uniform 50-kg bar in the figure is held in the equilibrium…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: What is the amplitude of oscillation of the 30 kg block of the system? - 2000 sin 1004 N 4 x 10° N/m…

A:

Q: Q2: Figure shows vectors P and Q. a. Represent position vectors P and Q in terms of their Cartesian…

A:

Q: A massless bar of length 1 m is pivoted at one end and subjected to a force F at the other end. Two…

A: Where: M - Moment about point O I   - Moment of inertia about point O α - Angular acceleration of…

Q: 3. The cylinder has a weight of 50 lb. Determine the force in each supporting cable AB and BC. Keep…

A:

Q: ty +x 20 m An incline of height 20 m and 0 = 12° has an object of mass m=1.5 kg sliding down on it.…

A: Inertia force diagram is drawn. Equation of motions are written in x and y directions. a=dv/dt is…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.