Answered: Is option B the correct choice? 10.…

Is option B the correct choice? 10. The output of a feed back control system is a function of a) Input signal b) Input signal and feed back c) Output signal and feedback d) Output signal

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.2P

See similar textbooks

Related questions

Q: How can I write the Verilog test bench and generate and verify the associated timing report of it?

A: 1module magnitude_comparator ( 2 input [3:0] A, 3 input [3:0] B, 4 output wire A_lt_B 5); 6 7…

Q: What is a simulation ? 1. A software like LabView O2. A dynamic system 3. Another name for Nyquist…

A: Simulation is the modeling of a given circuit or system by using different parameters and components…

Q: 27. A closed-loop control system requires the sensing unit (i.e. sensor) to send the system. (a) no…

A: In this answer we will find the correct option to which a closed-loop control system requires the…

Q: What is synchronization in digital control systems and mention some methods used to achieve it?

Q: An experienced technician who passes all eight basic ASE automotive certification test is cerified…

A: To have ASE certification the technician must pass in one certification area out of eight…

Q: Question 4 1. State the four programming languages described in the IEC 61131-3 standard. (4) 2. A…

A: 1. The four programming languages described in the IEC 61131-3 standard are: - Ladder Diagram (LD)…

Q: Which option is correct and why? 2. Which of the following are characteristics of a closed loop…

A: Closed loop control system:- It is designed to maintain the desired output of the system and is also…

Q: In an on/off control systems, to prevent rapid switching of control valve position an upper and…

Q: Industrial Motor Controls 15.a. A discrete input can be which of the following? A. −10–+10 VDC B.…

A: To select correct answer from given options

Q: please give me an accurate ans with 30 minutes tq

A: Step 1: Step 2:

Q: In a control system, to simplify the block diagram in it is done block diagram reduction. Some of…

A: According to the question, for a control system block diagram reduction, we need to discuss the…

Q: Where might a summing amplifier be useful in a control system?

A: Control system A control system uses control loops to manage, command, direct, or govern the…

Q: what is the STOP W.O.K.E Act

A: Florida state legislature, with the support of Republican Government- ‘Ron DeSantis’. passed a new…

Q: explain an instrumentation amplifier for dummies?

A: An operational amplifier is termed as an op-amp. Two inputs, a negative and a positive input is…

Q: What can open-transition starting cause?

A: Open transition starting is a method of getting motor to its rated voltage by reduction of applied…

Q: In swimming pools and water tanks, the water level needs to be controlled. To manage the water…

A: Automatic water level controllers are a product that was created to automatically control a motor,…

Q: In a closed-loop velocity servo system, if the load increases, the motor speed ["decreases",…

A: Servo motors operate in a closed-loop system, consisting of a feedback device, a drive (amplifier)…

Question

100%

Is option B the correct choice?

10. The output of a feed back control system is a function of

a) Input signal

b) Input signal and feed back
c) Output signal and feedback

d) Output signal

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

27. A closed-loop control system requires the sensing unit (i.e. sensor) to send the system. (a) no feedback (b) a positive feedback (c) a negative feedback to
1
Is it option B? 1. In an open loop control system the control action is dependent upon;a) the size of the system b) system variablesc) the input signals d) the output signal
For the following statements, indicate which feedback signal is applicable (position, speed or current): Position Controller Velocity Controller Current Controller Desired Position Pwr Position Velocity Current Motor Amp Current feedback signal Speed feedback signal Speed Sensor Speed sensor is mechanically coupled to motor shaft. Position feedback signal The loop controls motor torque
what is a voltage follower?
Which option is correct? 1. In an open loop control system the control action is dependent upon;a) the size of the system b) system variablesc) the input signals d) the output signal
MULTIPLE CHOICE -The answer is one of the options below please solve carefully and circle the correct option Please write clear .
25.a. The type of sensors that are used on most simple brushless motors to identify motor rotor position aretheA. field-effect sensors.B. optical-range sensors.C. hall-effect sensors.D. capacitive sensor. 25.b. An encoder is being used instead of a tachometer in a DC servo system. This system of speed control iscalledA. dual-purpose feedback.B. open-loop feedback.C. dual-connection feedback.D. bit counting.
9.a. A servo system is oscillating at standstill. This is an indication thatA. the following error limit has been exceeded.B. a motor winding is open.C. the system gain is too high. 9.b. In a DC servo motor system, the tachometer feeds back a voltage that’s proportional to motor speed.Where does this voltage go to?A. The interpolator cardB. The driverC. The CPU in the main controller
Q2) For a single phase (ac to ac) voltage controller, if the input supply voltage is (250Sin314t) with frequency (50 Hz) and the load is (R=5 Q). Draw the controller circuit, and then do the followings: - a. Determine the rms value of the output voltage at firing angle (a=60 ). b. Determine the value of (a) in order to obtain output voltage of (70.7 V).
please give me an accurate ans with 30 minutes tq
What fuels the amplification process and how?