Is main a caller/callee?Is manipulate a caller/callee?Is double a caller/callee?main:# a = 8#b =4jal manipulate# $s0beq $t4, $s0, main# loop based on resultsExitaddi $t4, $zero, 8addi $t5, $zero, 4jmanipulate: # inputs: a and badd $t2, $t0, $t1sub $t3, $t0, $t1jal doubleadd $t4, $t4, $t2$t5, $t5, $t4subjr$radouble:addaddjrExit:# inputs: q and r$v0, $a0, $a0$v1, $al, $al$ra=manipulate(a, b)# c = a + b# d = a# $t4, $t5#e = 2c + c# result = 2d=double(c, d)e# result1 = q + q2q# result2 = r + r = 2r=# exit instructions

This program is an assembly language program where manipulate and double are two labels which can be…

Is main a caller/callee? Is manipulate a caller/callee? Is double a caller/callee? main: addi $t4, $zero, 8 addi $t5, $zero, 4 jal manipulate beq $t4, $s0, main# loop based on results Exit j manipulate: # inputs: a and b add $t2, $t0, $t1 sub $t3, $t0, $t1 double jal add sub jr double: add add jr Exit: $t4, $t4, $t2 $t5, $t5, $t4 $ra # a = 8 # b = 4 # $s0 $v0, $a0, $a0 $v1, $al, $al $ra # inputs: q and r = manipulate(a, b) + b # C = a # d = a - b # $t4, $t5 = double (c, d) #e = 2c + C # result = 2d e # result1 + q = 2q # result2 = r + r = 2r #exit instructions

Is main a caller/callee? Is manipulate a caller/callee? Is double a caller/callee? main: addi $t4, $zero, 8 addi $t5, $zero, 4 jal manipulate beq $t4, $s0, main# loop based on results Exit j manipulate: # inputs: a and b add $t2, $t0, $t1 sub $t3, $t0, $t1 double jal add sub jr double: add add jr Exit: $t4, $t4, $t2 $t5, $t5, $t4 $ra # a = 8 # b = 4 # $s0 $v0, $a0, $a0 $v1, $al, $al $ra # inputs: q and r = manipulate(a, b) + b # C = a # d = a - b # $t4, $t5 = double (c, d) #e = 2c + C # result = 2d e # result1 + q = 2q # result2 = r + r = 2r #exit instructions

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Java programming using Conditional loop control
A user-input character or value is used to terminate which type of while loop? While loop eof is controlled, loop counter is controlled, and loop flag is controlled, while loop sentinel is controlled
Even though the EXIT clause can be used in any type of loop, it is considered good form to use the EXIT clause only in basic loops. Answers: Yes No
12
Python programming
Computer Science Part C: Interactive Driver Program Write an interactive driver program that creates a Course object (you can decide the name and roster/waitlist sizes). Then, use a loop to interactively allow the user to add students, drop students, or view the course. Display the result (success/failure) of each add/drop.
program must include a processing loop that allows multiple sets of data to be processed and the program should be terminated when there is no more data to process Develop a program in python that allows the user to enter a start value of 1 to 4, a stop value of 5 to 12 and a multiplier of 2 to 8. The program must display a multiplication table with results using these values. For example, if the user enters a start value of 3, a stop value of 7 and a multiplier value of 3, the table should be displayed as follows: Multiplication Table 3 x 3 = 9 3 x 4 = 12 3 x 5 = 15 3 x 6 = 18 3 x 7 = 21 Run the program with the following values: Start Stop Multiplier 2 10 4 4 12 6
QUESTION 9 Consider the steps you would take to write code that prints the output (below) meeting these criteria: • Use a while loop. • Declare a loop-control variable called noofSteps that is to be tested against 12. *****Output***** Step 1 Step 2 Step 3 <== Not part of actual output. .. Step 12 Choose the correct response to answer each question: 1) What is the means of stopping the while loop? 2) What is this while loop doing? 3) How is the loop-control variable modified? 4) Rather than testing noofSteps against 12, another valid test expression is
Please put these for loop steps in the right order. Answers Code following the body of the loop is executed The counter is compared to some value to see if the necessary condition is met The counter's value is updated A counter is initialized to some starting value The code in the body of the loop gets executed
Consider pseudocode in figure 2. a) Calculate_sum_and_average Set integer_total to zero Prompt for first integer Get first integer Prompt for integer DO integer_count = 1 TO first integer Get integer Add integer to integer_total ENDDO 1234567 2 5 6 8 68 9 average = integer_total / first_integer Display integer_total, average END Figure 2: Pseudocode Draw a solution algorithm using flowchart based on pseudocode in figure 2.
Computer Science 1 A while loop is a form of a pre - test loop, meaning that the loop condition is testing prior to executing the loop body. The loop body statements will not executed if the looping condition is not met. 2 The loop condition is a Boolean expression, returns true or false. 3 We continue looping as long as the looping condition is true. 4 The loop condition often has a sentinel value that once is reached the looping 4 The loop condition often has a sentinel value that once is reached the looping will cease. 5 The looping condition is usually associated with a counter that is incremented within the body of the loop. 6 A while() loop does not have a closing ; semi - colon. 7 A while() loop is often used to read an unknown number of records from a text or data file. We read and continue reading as long as we not reached the e.o.f. (end of file marker) 8 Beware of counter variables that may increment within a loop and erroneously a perceived value of the counter is…
(d) ires = 0; for index1 = 10:-2:1 for index2 = 2:2: indexl if index2 = 6 creak end ires = res + index2; end end number of times (outer loop) number of times (inner loop) R