is fixed at the bottom (point A) and fixed at the top (p between A and C, the column is braced in the y-direction

Q: Beam OC is suspended on rods 1, 2, 3 made of a material with Young's modulus E. The rods have…

A:

Q: Problem 1: A uniform beam of mass M = 100.0 kg and length L = 20.0 m has a load of m₁ = 3000 kg at…

A: According to the given data M=100kg Mg=100x9.81=981 N mL=3000kg mLg=3000x9.81=29430N T=12000N We…

Q: 3 cables with same diameter are used to hold the plate. Calculate the tensile loads in all cables if…

A: Givencables with load as  shown below

Q: The truss is supported by a pin at A and a roller at B. (Figure 1) Figure y 10 kN 2 m- 4 m- X 2 m 5…

A:

Q: Need help with all 4 questions please include all units and steps. Thanks

A: Step 1: Step 2: Step 3: solution is given above Step 4:

Q: 1. Construct a free-body diagram of the system shown in Figure 1. Neglecting the weight of the beam,…

A: The simply supported beam as shown below

Q: To use the equations of equilibrium for a three- dimensional object to solve for the support…

A: Draw the free body diagram:

Q: Write the vector expression for the position vector running from D to C; (i.e. rDC = ?) Write the…

A:

Q: A Ax = Bx = Ex = Number W Find the magnitude of the horizontal and vertical components of the pin…

A:

Q: 4. The structure shown in Figure 4 is subjected to the force of 45 kN, which acts in a plane…

A:

Q: Homework: Cables are attached to pins at A, B, and E as shown in Figure below. Determine the…

A: Given: The load acting on pulley, W = 200 N

Q: Find the horizontal and vertical components of the pin reactions at C and the magnitude of the…

A:

Q: Q4 The L2 steel bolt as shown in Figure Q4 has a diameter of 5 mm, and the link AB which is made…

A: Given: The diameter of bolt, d = 5 mm The width of rectangular section, b = 1x = 8 mm The thickness…

Q: The tractor shovel shown (Figure 4) carries a 500 kg load that has its center of mass at H. The…

A:

Q: Part D -A tractor shovel The tractor shovel shown (Figure 4) carries a 550 kg load that has its…

A:

Q: 1.2 m A 0.9 m B 0.9 m D P Figure 1 The structure shown in Figure 1 is used to suspend heavy items.…

A:

Q: The lower ends of the members of a 4-bar pined-joint truss shown in the figure below are fixed in…

A: Solution: Given Data: A→8,0,0B→0,10,0C→-8,0,0D→0,-5,0O→0,-20,20   To Find:

Q: The lower ends of the members of a 4-bar pined-joint truss shown in the figure below are fixed in…

A: Solution: Given Data: A→8,0,0B→0,10,0C→-8,0,0D→0,-5,0O→0,-20,20   To Find:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.