INVOLUTE SPLINE DATA: NO. OF TEETH DIAMETRAL PITCH 32 PRESS. ANGLĒ PITCH DIA PIN DIA MEAS. OVER PINS MINOR DIA MAJOR DIA 30 0.6875" 060" .7541" 10.0005 .6285"t.00 i (15.989mm ) .68495 t0.00025 CA- (17.398mm) 272.00 192.0 183.0 170.0 85.0 72.0 #13 CENTER PERMITTED BOTH ENDS 3.3 DRILL x 21 DP 4.5 C'SK X118 M4 X 0.7 TAP X 15 DP 63.1 (A 181.823 49.61 @ 15.00 N8, HEAT TREATMENT ENDUCTION HARDEN AREAS INDICATED TÓ RC A5-55 SEE HEAT TREAT TOTAL Rut OFLATHESS PERPENDIOLAR RNOUT - STRAIOTESS o CONCENRIctry O CERCLARITY Z NGLARITY 1OR/ PARALLEL ON SEE CHART FOR- INVOLUTE SPLINE DATA SYETERY O CYLINDRICITY SEE CHART FOR INVOLUTE SPLINE DATA MCTRIC SI METRIC SHARP CORNERS O ANGLE PROJECTION @ L.47 10.04 PAINT PEC USE COTO OR FORG SIMELAR TO ALTER PATT REVORK FIN PC MATERIAL SEE HEAT TREAT SEE HEAT TREAT 4 X SIZE TÝP. 2 PLCS. IULESS OTHERVESE SPECIFIED ALTERATIONG BY DATE ALTERATIONS BY DATE TBH JIM PART NANE SPLINE SHAFT 771-M XINTERNAL MACHINED RAD O5 MAX CHANFERS ARE 45 XFENISH ALL OVER ANG TO.O5 DEG XREAK EDGESOI TO O4 ADDED HEAT TREAT TO GRcOVES UNIT PEPLACES 10-10319 HODL ULT-CTR TURRET HSG N7 monarch Sidney 10-10934 SIONEY, OHto, USA 45366 Ø12.00 09 SIO Ø15.60 Ø15.60 RO.13 MAX TYP p15.96 ±0.06

Q: From among the following select the truest statement. The Distortion Energy theory is a special case…

A: The given problem is based on theory of failure.

Q: e hóldéř óf m öf å d to expose th

A: to obtain a mining lease , the holder of a mining claim must absolutely acquire surface rights .

Q: how do i make this in creo parametric using grouping and pattern features

A: To create the concentric square patterns in Creo Parametric as shown in your image, you can follow…

Q: Epidemiological studies are all lutant concentrations. In all such studies there is the hazard that…

A: Air pollution is caused by solid and liquid particles, as well as some gases that are suspended…

Q: Required information Three blocks A, B, and Cand a grooved block D have dimensions a, b, c, and das…

A: Calculated the mean gap and it's tolerance .

Q: What best describes this print? * A. Casting B. Forging C. Welding D. Machining 2.  There are GD&T…

A: First of all, In the given Engineering drawing the Rotor assembly is given and its parts are drawn…

Q: The last 3 compartments in a feature control frame provides the datum references; this is known as…

A: The last 3 feature control frame provides the datum referances, this is known as datum order of…

Q: I need help answering questions 1,2, and 3 pertaining to the print attatched below.

A: 1stIn the given drawing there are 4 surface texture symbols.

Q: What company specification number is given to the material for this part?  2. What is the revision…

A: First of all , this engineering drawing shows the detailed assembly drawing of KM50 Head with the…

Q: Match the following statements with the term that best describes each statement.  hooks law creep…

A:

Q: I need answers to parts 7, 8, and 9, pertaining to the print provided.

A: What is the basic height of this assembly as shown in the section view?Refer the front section…

Q: I need answers to questions 13, 14, and 15 pertaining to the print provided. Note: A tutor keeps…

A: 13.Calculate the maximum material condition for the largest cylindrical part feature.

Q: I need help answering these two parts pertaining to the print provided below.   What name is given…

A: In the given print, the schematic view is shown at the upper left corner of the print, Auxiliary…

Q: QUESTION 3 The design calculations for a rod, which is subjected to static loading conditions and a…

A: As given the yielding diameter is 0.74cm So, for limiting case the diameter will be 0.74cm and safe…

Q: The magnitude of F₁ is 58.7 The angle for F₁ is 0₁ 909.36 XN X

A:

Q: I need help answering problems 4, 5, and 6 pertaining to the print provided in the attachment.

A: The print sheet is showing the 3D view or perspective of the lower support cylinder union part.

Q: The is the condition in which a feature of size contains the least amount of material within the…

A: Maximum material condition: The condition of the object in which the object have maximum amount of…

Q: 7-Either the following text: Standardization is an activity that consists of developing rules…

A: It is asked to generate stick scriptWhat is te role of orientation marker How the inscription…

Q: I need answers for problems 13, 14, and 15 pertaining to the print provided.   NOTE: If you refuse…

A: 13.A characteristic of a system which may cause failure or defects if not in line with quality…

Q: What company specification number is given to the material for this part?  2. What is the revision…

A: Engg drawing is a technical drawing that is used to transfer the information from the design to the…

Q: Explain the purpose of the feature control frame below clearly and completely. Datum A is the size…

A: A feature control frame used to describe the conditions and tolerance of a geometric control on a…

Q: 11. Parts or features requiring a rounded edge or corner are identified with whi 12. D Features that…

A: In geometric dimensioning and tolerancing (GD&T), an interesting set of GD&T images are…

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.