B) What is the difference between? 2-Internal and External flow

Q: 1. Air (p= 1.23 kg/m³; = 1.79x107 through a 0.08-mm-diameter passa person's lungs at a rate of 10-9…

A:

Q: ) Consider the 2D beam supported by a roller at A and a pin at B. INTERNAL FORCES c) Draw the…

A:

Q: Water flows through a 100 mm diameter pipe with a velocity of 0.015 m/s. If the kinematic viscosity…

A:

Q: Design a sliding gate wing type of beams (w8*40) which have an elastic section modulus equal to 582…

A:

Q: The limit of proportionality in the material of a structural steel member, when subjected to simple…

A: Given data- A structural steel member- Simple tension-σy=280 N/mm2Principal stress-σ1=122 N/mm2…

Q: Q.4 X A plane blow leak velocity component u = y V=- and w = 0 along x, y T₂ and z direction…

A: Given- Leak velocity components- u=xT1,v=-yT2,w=0, It is needed to find the relation for blow to be…

Q: Question A cylindrical soil specimen of saturated clay, 3.50 cm diameter and 8 cm length, is tested…

A: Given data- A cylindrical soil specimen- Diameter D=3.50 cm, Length L=8 cm, Failure load =50 kg,…

Q: Q.1) For the system shown in figure, what is the value of the force P applied at joint D to maintain…

A: The free body diagram for the section is shown below:

Q: A 60-kg disk supported by the rope and was rests against a rough vertical wall. The tension of the…

A: The pulling force that acts along with a rope is called tension (T). When a rope supports the weight…

Q: Problem 1 メ=7 A scaled model of a proposed dam is used to predict the flow conditions in the…

A: Given data-

Q: 1.) Draw the Free-Body Diagram for each mechanism shown. Provide a direction a a name for each…

A: To draw FBD

Q: Please provide a complete solution in a sheet of paper.

A:

Q: According to available data shown in Tables 2, calculate the following: a. Compute the desired…

A:

Q:  please provide me with the step-by-step solution

A: Given: SystemDollar (Cost)TonMinuteDollar per ton per…

Q: = What is the gage pressure [in psi]... Water Air Oil (SG=0.8)

A: Given:Required:Gage pressure at bottom of tankGage pressure in the air zone in the container

Q: Let w = [w] lb/ft. p) Determine the maximum shear Vmax in the beam. q) Determine the maximum bending…

A: Given  W= 250 lb/ft

Q: Describe Consistency in the Remolded State and Plasticity.

A: Consistency Limit:

Q: 4 m 3 m 0.5 m 0.8 m B 20 kN 160 kN 20 kN 40 kN Find the value of the moment of 4 forces acting on…

A: The FBD of the system is:

Q: 3.) Consider the 2D frame shown below. There are pins at A, C, D. Point E is halfway between A and…

A:

Q: The circular water pipes as shown in the figure are flowing full. The velocity of flow in the branch…

A:

Q: A boat is towed at the rate of 12mi/hr. At t=0, the towing line is cast offand a man in the boat…

A: A boat is being towed at the rate of 12 mi/hr. At the instant (t = 0) that the towing line is cast…

Q: What is the difference between vapor pressure and Henry's Law constant? What is an application of…

A: Answer:- Vapor pressure:-  When a liquid comes in the contact with the air, a fraction of it will go…

Q: FORMULA: The formula for calculating the water content for Plastic limits is as follows: W1 – W2…

A:

Q: 1.) The simple machine shown below has 2 parts connected via a pin at A. The gripping teeth at B…

A: The given figure is shown below:

Q: Consider the 2D beam supported by a pin at A and a roller at B. EXTERNAL FORCES a) Draw a FBD.…

A:

Q: A suppressed rectangular weir in a rectangular channel of width 2.6 m carries a discharge with a…

A: Given - Width, L = 2.6 m Head, H = 0.30 m Coefficient of discharge, cd = 0.63 To find -  Discharge…

Q: H.W.1: A steel bar 6 m long is 5 cm in diameter for 3m of its length and 2.5 cm in diameter for the…

A: Given: For First 3m bar, Diameter=5cm=0.05m Length=3m For second 3 m bar Diameter=2.5cm=0.025m…

Q: Q.13 Two reservoirs connected by a pipe of friction factor 'f 'has a difference in water surface…

A: 2 reservoirs connected by a pipe-Friction factor=fDifference in water surface elevations=HH & f…

Q: List 10 applications of Compressibility ( a property of fluid

A:

Q: A cantilever beam 10 ft long is subjected to a uniformly distributed load of 1500 lb per ft. of…

A:

Q: Water is pumped through a pipeline to a height of 10 m at the rate of 0.1 m³ /s, friction and other…

A: Friction and other minor losses hf= 5 mHeight  H = 10 m  Rate of flow, Q = 0.1 m3/s  Pumping…