inputs (a, b, c, and d). The circuit is described by the following Boolean expression. A static one hazard occurs when

Q: Convert the OCTAL NUMBER 4033.347 2 to decimal number (show the steps in paper , scan and upload…

A: The octal number can be converted into decimal number directly given as:…

Q: The -------parameters may not reflect the actual operating conditions but simply provide an…

A: 1. The advantages of the re model are that the variables are determined by the real operating…

Q: Question 2 Q. Calculate in binary 11111.11/11111.1*111.1

A: Given, 11111.11/11111.1*111.1 According to BODMAS, D means division and M means multiplication.…

Q: Which of the following statement/s defines a control system?(select 3) control systems can move…

A:

Q: A supermarket has a one entrance-door and one exit-door. The customer capacity of the supermarket is…

A: According to the question, we need to write the FBD program.

Q: Q1: Explain the difference between flipflops and latches.

A: Flip-flops and latches

Q: IGBTs have asymmetric voltage blocking capabilities is called ....... IGBT

A: Asymmetrical IGBT :-  => In this type of IGBT reverse breakdown voltage is less than forward…

Q: Develop a simple Arduino-based System that will utilize TIMER and LED. Present your answer in the…

A: It is asked to develop a simple Arduino-based System that will utilize TIMER and LED.We need to…

Q: • Sensors on 3 landing gear • The pilot has a Gear Down Control switch • When the Gear Down Control…

A: The required logic design can be obtained by using the truth table derived based on the given…

Q: What is program block and module .What is difference between "==" and "==="

A: Reg is driven by always  block it can't be driven by continuous assignment statement. Always block…

Q: Complete the number conversions indicated. Note that all binary numbers are two’s complement…

A: A binary number is a number which is expressed in base-2 system by using only "0" or "1" digits.…

Q: 5. Explain the application of DSP in mobile phones

A: DSP is known as digital signal processor these DSP are fabricated in chips which are integrated in…

Q: Draw and explain the working of BCD counter along with truth table and timing diagram.

A: We need to design a BCD counter which can count from 0 to 9 only. Now the truth table will be

Q: Find the minimum size EMT raceway required to carry three (3) 500kcmil, three (3) 3/0AWG and two (2)…

A: When all conductors are the same size and have same insulation, NEC Table C.1 gives trade size base…

Q: What is sequential circuit? **please typing via keybord not handwriting**

A: A Sequential circuit combinational logic is circuit that consists of inputs logic gates…

Q: 1- If the LED was connected to pin 5 and the delay was 3 seconds. Modify the code to accommodate…

A: Given the circuit, as shown below: The following code is applied to the circuit as shown below: If…

Q: 1. Outline/Give Two examples for job factors that could lead to poor/bad health and safety behaviour…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Question 8 Electric field terminates at.. Negative charge Positive charge Both positive and negative…

A: Electric field is present in the vicinity of energized materials( namely active conductors etc.).

Q: e huge generators that are used to feed large facilities such as factories, companies, hotels and…

A: The main reason for using self excited dc generator is that self excited dc generator are less…

Q: A. Condition 1 You have 2 push buttons and 1 lamp. The lamp will turn "ON" if either of the 2 push…

A: We need to create a PLC program for the following conditions  The lamp will be turn ON if either of…

Q: Consider the following sequential circuit. Determine its state table and state diagram. A Cp

A: Given the sequential circuit as shown below: We need to determine the state table and state…

Q: Define noise in communication systems and mention the different types Note: Please do not…

A: Noise is an unwanted signal which interferes with the original message signal and corrupts the…

Q: H/W Convert this simple timeline to include all the necessary pins: One Bus Cycle T2 T3 T4 CLK-…

A: In 8086 microprocessor  pins from 16 to 2 i.e,AD0 to AD14  pin-39:AD15  pin-38:A16/S3 pin-37: A17/S4…

Q: What are the different onboard sources of electrical power in a modern commercial passenger…

A:

Q: 13-Find the Thevenin and Norton equivalent circuits between ab. 2 A a 6 0 18 V 3 A 10 V

A: Given:

Q: Which of the following statement/s defines a control system?(select 3) control systems can move…

A:

Q: 1. If they are present, what items are required to be bonded together to form a grounding electrode…

A: There is the duty of the electrician to be assure that all conductive materials are properly bonded…

Q: 7. Using De Morgan equivalent gates and bubble pushing methods, redraw the circuit in Figure 3 so…

A:

Q: Discuss the difference between the off-line and online UPS

A:

Q: Draw the block diagram and describe the principle of operation of the UPS type inline-interactive

A: When power is lost, a line-interactive UPS keeps the inverter in line and changes the battery's DC…

Q: Please explain how the schematic diagram (NOR) works. I will give thumbs up after!

A:

Q: Match the appropriate number with the given statements. 4 DIGITAL (PWM-) OO UNO TX ON ARDUINO RX…

A: Given,

Q: ANSWER FAST PLEASE, Show Step By Step, NO AI or chat GPT

A: we need to match given property and phrase.

Q: Programming the device involves the blowing of internal fuses to achieve a desired_________________…

A: PLD is an IC that contains enormous no of entryways, flip-flops, and so forth that can be arranged…

Q: Problem 1 Given the timing diagram below showing two writes executed consecutively, and knowing that…

A: Microprocessor and microcontrollers are used for data processing. Logic and control are used for…

Q: Discussion:- 1- Why the asynchronous counter called ripple counter? 2- Why the asynchronous counter…

A: LATCHES: Latches are a basic memory element that is used to store one bit of information. Types of…

Q: Complete the wiring below, such that the two sensors are connected in series and capable of…

A: Two proximity sensors, one load and one power supply is given in the question. We need to complete…

Q: 4. current overloads. " and are used to protect circuits against

A: In this question, we need to fill the blanks. What are the name of devices which are used to protect…

Q: 8: A solar cooker uses hot air to cook food. Select one: True False 19: text _____________ can be…

A: Solar cooker is device that converts direct sunlight to heat, cook food materials.

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.