Input 1 ² Input 2 Output Differential Amplifier Figure 2-2: Differential amplifier 1 1. From figure 2-2, what will be the output signal if both input signal has equal amplitude but 180° out-of- phase with each other? The output signal will be the sum of two inputs signal and therefore greater than the input signal. The output signal will be the sum of two input signal and therefore making the output signal equal to zero. The output signal will be the difference of two input signal and therefore greater than the input signal. The output signal will be the difference of two input signal and therefore making the output signal equal to zero.

Input 1 ² Input 2 Output Differential Amplifier Figure 2-2: Differential amplifier 1 1. From figure 2-2, what will be the output signal if both input signal has equal amplitude but 180° out-of- phase with each other? The output signal will be the sum of two inputs signal and therefore greater than the input signal. The output signal will be the sum of two input signal and therefore making the output signal equal to zero. The output signal will be the difference of two input signal and therefore greater than the input signal. The output signal will be the difference of two input signal and therefore making the output signal equal to zero.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1-C) Which op-amp IC is more suited for digital applications, and why?1-D) Which op-amp IC is more suited for instrumentation applications, and why?
These questions from electronics lab course, from The common Collector Amplifier (Emitter-Follower) Experiment.
Question 3 The 555 timer is connected in the following circuit. The resistance of the extra resistor is 102, the capacitance of the extra capacitor is 0.1F. The voltage input at Pin2 is Vcc. What is the output state at Pin3? 1) 2) Decide the voltage input value at Pin 6 when the condition is stable. 3) Decide the output state at Pin3 when a trigger input is applied at Pin2 (voltage input at Pin2 changes from Vcc to 0, and return back to Vcc immediately). 4) After the trigger input is applied at Pin2, how long would the output maintain at the unstable state. Vc R O Output Vo 555 Vc 0.01µF Trigger Input
Prob 1: For each of the 8 circuits below, draw small signal model and calculate Vout/Vin. Vb1, Vb2 are dc voltage sources. and I1 is an ideal dc current source. Ignore body effect for all problems. Vino M3 M₂ M₁ (a) VDD J Vb₁ M3 (e) VDD VinM₂ Vb2M₁ Vb3 Vb2 - Vout Vb1 Vout HE Vout o Vb₁ VinM₂ 46! M3 (b) VDD B M₁ T. M3H (f) VDD VinM₁ M₂ Vout VinM₂ 4M₁ (c) M3 M3 VDD VDD 74 Vb1M₂ Vino M₁ (g) Vout Vout Vb1 Vb2 HE Vin VinM₂ M3 M3 VDD (d) HL M₁ M₁ -o Vout M2o Vout 1₁ (h) VDD
Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? What is the value of Vin?Vin = ____ volts
For Steady-State Operation o f Boost DC-DC Converter What is the duty ratio (D) How can it effects on the converter output (Vo)
(b) Draw the circuit of an isolated step-down DC/DC converter and explain how it works. In your answer, explain how electrical isolation is kept while the output is regulated to the desired output voltage.
1. For the pointer position in the diagram, what is the input signal if the range is set at 0.3 V? A. For the pointer position in the diagram, what is the input signal if the range is set at 1 V? B. For the pointer position in the diagram, what is the input signal if the range is set at 30 V? C. Let’s say you know that the input signal will be about -0.25 V. What range should you select to give maximum deflection without going off scale? Draw a line, with a straight-edge, on the picture above, showing how the pointer would point.