initialized to 22. Suppose you executed the code below on a version of the pipeline from your textbook that does not handle data hazards (i.e., the programmer is responsible for addressing data hazards by inserting NOP instructions where necessary). What would the final values of registers X3 and X4 be?

initialized to 22. Suppose you executed the code below on a version of the pipeline from your textbook that does not handle data hazards (i.e., the programmer is responsible for addressing data hazards by inserting NOP instructions where necessary). What would the final values of registers X3 and X4 be?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Question 2: Write complete code for a 16-bit assembly program that includes a subroutine and a call to that subroutine. The subroutine should add the value 2 to the register BX. (You may use the back of this sheet to write your code.)
You have studied Rotate Instruction of 8086 microprocessor in Computer Organization & Assembly Language Programming course. The Instructions were (ROL, ROR, RCL and RCR). Design a circuit that is given a 3 – bit number as input. The circuit rotates the input number 2 times to right (ROR instruction). HELP ( Just calm down. Forget ROL, RCL and RCR instructions. Just recall the logic of ROR instruction. Be very careful in drawing the truth table. Rest is easy.
I need to write a basic code on C, That completes the following taks:
An 'instruction fetch/read' results in three sets of numbers that go to the Registers Block as studied in class. These three numbers in the instruction represent bits 25-21 for 'Read Register 1', bits 20-16 for 'Read Register 2', and bits 15-11 for the 'Write Register'. What does the 5 bits width of each of these indicate? a. That the word is 15 bits long in this architecture b. That each word is 32 bits long c. That there are 32 registers that can be addressed in this architecture d. That there are 15 registers that can be addressed in this architecture
Using MIPS assembly Calling a Subroutine Make your multiplier code into a function, and call it from a main. You must pass the two numbers to be multiplied into your function using the $a0 and $a1 registers, and return the answer back to main using the $v0 register. Do not load from your .data section or store to your .data section inside the function. You may load from and store to the stack, of course. After the multiplied value has been returned to main, you should place it into a main memory location and then print out the result using syscall. A sentence like "5 times 6 is 30." should be printed out in the terminal.
Please solve and show all work. For the following C statement, what is the corresponding MIPS assembly code? Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively. Assume that the elements of the arrays A and B are 8-byte words: f = (g+i+2) + (h − 8); B[8] = A[i-9] + A[j+8] + 7;
This is a block diagram of a microprocessor. Inta Rst 6.5 Trap Rst 7.5 Intr Rst 5.5 SID SOD Interrupt control Serial I/O control 8-bit internal data bus Accumulator Instruction decoder (8) Temp reg. (8) Flag (5) flip flops B C. Reg (8) (8) Instruction Reg Arithmetic decoder D (8) (8) and Reg Reg logic unit L (8) (8) Reg Register array machine Reg (ALU) (8) cycle encoding Stack pointer (16) Program counter (16) +5 V GND Power supply Incrementer/ decrementer address latch (16) Timing and control Reset CIk Gen Control Status DMA Address buffer (8) Data/address buffer (8) RD WR ALE S, S, IO/M Hold Clk out Hlda Reset out Ready Reset in A1s-Ag To Address bus AD-AD To Address/data bus
(a) In MIPS machine language, the R format instructions need an additional field (the “funct” field) to specify the instruction type (“add”, “sub”, etc.). Why can’t this be done using just the 6-bit “op” field, which all MIPS instructions have, instead? (b) Give a sequence of MIPS assembly language instructions that adds the contents of $s0 and $s1, storing the result into $s0, if the contents of $s1 are greater than 6. Otherwise, the contents of $s0 should be incremented by 28. In either case, afterwards the contents of $s0 should be copied into $s2. (c) Suppose that the starting address of an array of words is stored in $s0. Give a MIPS assembly language instruction that loads the contents of the second word in the array into $s1. (d) Suppose that A and B are defined using “A: .word 0”, and “B: .space 100”. Give a sequence of MIPS assembly language instructions that calls a procedure “P” with its two arguments being the contents of A and the address of B, using the standard procedure…
Assume the initial value for X1 is is 11 and X2 is 22. Suppose we execute the code below on a version of the pipeline from your textbook that does not handle data hazards (i.e., the programmer handles data hazards by inserting NOP instructions where necessary). What would the final values of register X5 be? Assume the register file is written at the beginning of the cycle and read at the end of a cycle. Therefore, an ID stage will return the results of a WB state occurring during the same cycle. ADDI X1,X2,#5 ADD X3,X1,X2 ADDI X4,X1,#15 ADD X5,X1,X1