Answered: Industrial pipes: Can we…

Industrial pipes: Can we perform hydrostatic testing immediately after completion of welds (less than 48 hours) on pressurized parts of pipelines?

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter15: Gas Metal Arc And Flux Cored Arc Welding Aws Sense Certification

Section: Chapter Questions

Problem 19R: What shielding gas mixture and flow rate are recommended for the GMAW-S SENSE pipe workmanship...

See similar textbooks

Similar questions

A certain type of cans are formed on a machine by spinning them from cardboard stock and attaching a metal bottom panel. By inspection of a can, we may determine whether, when filled, it could possibly leak either on the side seam or around the bottom joint. Such a nonconforming can has an improper seal on either the side seam or the bottom panel. Sample size =50.Determine wither this method is operating in control or not?What is your suggestion?
Question 4 A team of engineers tasked with the design of a pipe system is currently sizing some of the different subsections. The team has started by identifying two types of pipes, each of them involving different fluids (water and glycerin) as shown in Figure 4 below. Material roughness is e = 10μm for both. D₁ = 0.1m D₂ = 0.15m (a) (b) V₂ Section 1 Pw=999 kg/m³ P = 0.00112 N-s/m² P₁ = 1260 kg/m³ #₂ = 1.5 N-s/m² Figure 4 Section 2 Pipe 1 (water) Pipe 2 (glycerin) 1.1D₂ 1.1D ₂ Consider only Section 1, where pipe diameter is respectively Di and D2, and estimate the head loss per meter when the volume flow rate within each pipe is Q=0.05 m³/s. Refer to the given values of density (p) and dynamic viscosity (u) indicated in the figure as well as to the Moody chart in the next page where appropriate. As also shown in the figure above, the diameter of the pipe increases by 10% across a sudden expansion for both cases. What is the head loss per meter over Section 2? In order to account for…
QUESTION 5 Assuming a cylinder of molten plastics with a starting radius of 8.8mm and hieght of 1.8 mm, what is fe height after 4 sec, if a force of 57 N is applied. Assume a viscosity of 1,082 Pa*sec.
Q1. Well water contained in an AISI 304 SS pipe network for chemical treatment and posterior distribution by aerial water pipes to different locations in a food manufacturing facility was analysed. The AISI 304 SS pipe network had an approximate 300 m length, 154 mm diameter and 2.0 mm wall thickness. The AISI 304 SS pipes were welded using a Tungsten Inert Gas (TIG) welding procedure. In-situ weld quality assurance was tested by pressurized WW, and no pinhole leakage was detected. After the pipe network remained out of service for 6 months at room temperature containing stagnant, pressurized well water, pitting corrosion was observed on the weld joints and the base material by the presence of multiple pinhole leaks.(a) Discuss, with chemical equations if relevant, TWO corrosion events that may have caused the pitting corrosion.(b) What practical steps could have been taken to mitigate for this potential outcome?(c) Identify corrosion inhibition methods to mitigate for the corrosion…
please help me answer this question. I really need the answer. Thank you so much!
What is compression testing?
advantage and disadvantages of using STRAIN GAUGE
110 About indistrial piping WHY IS THE ASME 31.3 ALLOWABLE STRESS A COMBINED STRESS?
T3.2.2 The bracket shown below supports an 18 kN load. The fillet weld extends for full 100 mm length on both sides. What weld size is required to give a safety factor of 3.0 if E60 series welding is used? [Ans. 10 mm] 100 mm 18kN 75 mm Note: There are two 100 mm welds. 1
These are the questions and the corresponding figure for the questions, make sure for each question the answers are neat and readable.
When do stress concentrations occur?
Cal. the permeability number of a sand specimen if it takes 75s to pass 2000 cm3 of air at a pressure of 6 g/cm2 through the standard sample.