incd from a large reservoir using two horizontal plastic pipes connected in series. The irst pipe m long has a 10-cm diameter, while the second pipe is 35 m long and has a 5-cm diameter. The water level in the reservoir is 18 m above the centerline of the pipe. The pipe entrance is sharp- edged, and the contraction between the two pipes is sudden. Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir. 18 m Water tank 13 m 35 m

incd from a large reservoir using two horizontal plastic pipes connected in series. The irst pipe m long has a 10-cm diameter, while the second pipe is 35 m long and has a 5-cm diameter. The water level in the reservoir is 18 m above the centerline of the pipe. The pipe entrance is sharp- edged, and the contraction between the two pipes is sudden. Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir. 18 m Water tank 13 m 35 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pumped storage power plant with a head of 150 m, with a flow rate of 6 cms for power generation and pumping, and continuous operation for 8 hours each time. Try to find (1) the power output during power generation and the total daily power generation; (2) pumping water Hourly power and total daily power demand; (3) Pumped storage power plant efficiency; (4) Adjust the pool capacity? Assuming that the water loss is 8% of the total drop, the combined efficiency of the turbine and generator is 85%, and the efficiency of the pump is 65%.
In a pumping system handling water, the level in the suction tank is 3.2m below the pump shaft centerline; and the level in the discharge tank is 21m above the pump shaft centerline. The inlet piping is 7.6cm in diameter and together with its valves fittings is equivalent to 26m straight pipe. The discharge line, 6.35 cm in diameter, with its valves and fittings is equivalent to 72 m straight pipe. If the motor delivers 7.1 kW to the pump shaft, what is the pump efficiency for discharge rate of 12.63 Ips? Assume f = 0.023
A hydraulic reaction turbine working under a head of 16 m develops 640 kW of power. What is the unit power of the turbine?
When a pump with a suction and discharge pressure of 125 kPa and 409 kPa are used, the flow rate is 30L/s into a pipe with a diameter of 4 cm. Approximately 10cm in diameter, the suction diameter. What is the energy added to the water by the pump in meters
Water with density of 998 kg/m3 flows through an inclined pipe with diameterof 8 cm. At section A, pressure and elevation level are 175 kPa and 23.5 m,respectively. Meanwhile, pressure and elevation level at section B are 255 kPa,and 8.5 m, respectively. Determine the head loss and show direction of flowingwater.
Q3: Compare the volumetric flow rate of water through a pipe inclined at 30° to the horizontal having an inside diameter of 0.2m when it is fitted with: (a) Venturi meter with an I.D of 150mm at the throat and a discharge coefficient of 0.98. (b) Orifice plate has a hole of diameter 10cm and a discharge coefficient of 0.65 The difference in manometer head connected across both meters is 40 mm of mercury.
I need the answer as soon as possible
A vertical circular tank that is 1.5 m high, has sloping sides. The tank is 50 m and 30 m in the top and bottom diameters respectively. Discharge takes place through a triangular orifice situated at the bottom of the tank. The orifice has a base of 0.8 m long, 0.5 m below its vertex. If the tank is originally full of water, what time is required to empty the tank? Take discharge coefficient as 0.63
In Fig. is shown a plot of pump net head as a function of pump volume flow rate, or capacity. On the figure, label the shutoff head, the free delivery, the pump performance curve, the system curve, and the operating point.
A pipe of 0.25 m diameter carries water at the rate of 7.2 m3/s.The pressure head at the entry of the venturimeter, used to measure the flow rate in the pipe, is equivalent to 6 m of water. If the pressure head at the throat is zero, calculate the throat diameter of the venturi.Include fbd.
on the island, hydropower is expected to be extracted from a river of the river system via a pipe, 74 m long, to a turbine.During the dry season, from February to May the average daily flow rate of the river is 35 m3s-1 and for the remaining 8 months, the average daily flow rate of the water is 115 m3s-1. Assume, the initial capacity expenditure evaluated on a yearly basis of the run of a river system is $900 000, the annual operating cost is $17 500; and the density of water is 1000 kg ∙m-3.Considering the run of the river system above, determine(i) the energy potential at the source for one year,(ii) the levelized cost of electricity, and(iii) compare the LCOE value and the cost of electricity, and comment on the capital investment.
As shown in figure below, oil can be siphoned from a tank using a flexible hose, provided that the end of the hose at Point B, is below the free surface in the tank at Point A. The maximum elevation of the hose is at Point C. Oil is being siphoned from the tank through a constant-diameter hose. The end of the siphon at Point B is 6.71 meters below the oil top surface level of the tank at Point A. If the gauge pressure at Point C is 90.257 KPa and the density of oil is 890 fraction numerator k g over denominator m cubed end fraction , the vertical distance between Point C and Point B in meters is