In order to drain the tank faster, a pump is installed near the tank exit. Determine how much power input is necessary to establish an average water velocity of 4 m/s when the tank is full at 2 m. diameter is 10cm

Q: A manufacturer states that their gear pump requires 0.85 hp to pump 9 gpm of oil (sg=0.90) with a…

A: The flow rate of the oil is, Q=9 gpm. The specific gravity of the oil is, SGo=0.90. The total heat…

Q: please explain how to get the friction factor

A: The objective of the question is to calculate the friction factor, the power supplied to the pump,…

Q: A water tank with a very large cross-sectional area, open at the top, has a very small hole drilled…

A:

Q: 1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm…

A: Given data  Flow rate = 500 gpm Pressure = 35 psi Density = 62 lbm/ft^3 Find the pump head

Q: Problem 3 – Water from a large tank flows thru the pipe system shown at a rate of 10 ft³/s and…

A:

Q: A water discharge of 8 m3 s is to flow through this horizontal pipe, which is 1 m in diameter. If…

A: Given Data⇒ Discharge Q=8m3s Horizontal Pipe Diameter of pipe(d)=1 m   Assumptions made in…

Q: There are three main categories of dynamic pumps. List and define them.

A: Dynamic pumps are typically the main pumps generally used for large flows with lower pressures. They…

Q: Using the pump selection table below to determine the best pump for the given condition: A flow of…

A: Given data as per the question Flow rate =150 m3/h =41.6667 L/S Head =50 m

Q: What is the velocity of the pipe center (m/s)? Given that h3%-88.3 cm h3 h2 =7 cm h =3 cm] Water

A: hps=88.3+7hps=95.3 cm or 0.953 mhp=7 cm or 0.07 m apply bernoulli's equation between 1 and…

Q: Francis and Kaplan turbines are often provided with drafttubes, which lead the exit fl ow into the…

A: A draft tube can be defined as a pipe of gradually increasing area that connects the outlet of the…

Q: For transferring of water, a pump is installed in the height of 3 m above the surface of the water.…

A: hsp=Pρg=100kpa1000×9.81=10.19hs=3mhf=4mhvp=Pvρg=10kpa1000×9.81=1.019

Q: For a hydroelectric plant, a hydraulic turbine-generator is installed at the site below the free…

A:

Q: According to Figure 1, information given de= 500mm, Ve= 7.0 m/s, h= 5.0 m and PB= 105 kPa.…

A: i. The pump head is 41.2 m. The discharge of water is 1.37 m3/s. The pump power is 555.5240 kW.…

Q: Water is supplied in a 2-in. dia. pipe at the rate of 2 cfs to a 10-hp, SO-percent efficient pump.…

A: The Answer is below

Q: I have a question from my fluid power enginneering class. The question was, standard hydraulic oil…

A: Given: Pressure at the pump outlet is 10 psi. Height of uphill is 100 ft. Flow rate is 10 gpm.

Q: The density of water is loon tkg/a? and the e elective bulk modlus (k) is that ombong Carries water…

A: Since you have asked multiple questions in a single request we would be answering only the first…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.