In the syringe as shown in the figure, the drug has 900 kg/m3 and an absolute viscosity μ = 0.002 Pa – s. Neglecting head loss in the larger cylinder. Determine the value of the Reynolds number for a flow of 0.4 mL/sec. through the needle. Determine the force required to produce a flow of 0.4 mL/sec.

In the syringe as shown in the figure, the drug has 900 kg/m3 and an absolute viscosity μ = 0.002 Pa – s. Neglecting head loss in the larger cylinder. Determine the value of the Reynolds number for a flow of 0.4 mL/sec. through the needle. Determine the force required to produce a flow of 0.4 mL/sec.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pls fast hand written solution
The results of the COD analysis performed on a 100-mL sample containing 103 mg of glucose (C6H12O6) are given in the table below. The amount of FAS used for the blank and for the determination of the FAS normality is 9.92 mL and 20.34 mL, respectively. Calculate the COD concentration of the sample and comment on the COD to ThOD ratio.
A capıllary glass tube of 0.1 mm internal diameter is immersed vertically in a beaker full of waten Assuming the tube to be perfectly clean and wet, determine the height of the capillary rise of water in the tube when the room tamp is 20°C. Given at 20°C unit weight of water = 0.9980 gm/cc and surface tension 72.8 dyne/cm. %3D
The projectile shown is launched at Vo = 96 m/s at 50° above the horizontal. The surface on which it lands is described by the equation shown. Determine the abscissa of the point of impact. ROUND OFF TO TWO DECIMAL PLACES, INCLUDE THE SIGN OF THE FINAL ANSWER. y Vo y = -0.001x²
Q3: A tube has a u-shaped, as in the following figure, if the density of water is 997 kg / m3, the concentration point of mercury is 13550 kg / m3, find the height of the fluid (h )shown in the diagram and the amount of pressure (P) at point a, b, d, and c? Water- |0.3m Mercury
I need the answer quickly
Read the question carefully and give me right solution according to the question.
Figure P2.33 shows a portion of the H,O-NaCl phase diagram. 10 Liquid (brine) Salt Ice + -10 F liquid (brine) liquid (brine) -20 Ice + salt -30 NaCI 10 20 30 H2O 100 90 80 70 FIGURE P2.33 Composition, weight % a. Using the diagram, briefly explain how spreading salt on ice causes the ice to melt. Show numerical examples in your discussion. b. At a salt composition of 10%, what is the temperature at which ice will start melting? c. What is the eutectic temperature of the ice and salt combination? Temperature, °C
- GET THE GIVEN, WHAT IS ASKED, AND THE ANSWER. - MAKE A PROPER FREE BODY DIAGRAM. (IT DOES HAVE THE GREATER POINTS IN THIS ACTIVITY) - YOUR SUB ANSWERS MUST BE IN 6 DECIMAL PLACES. - YOUR FINAL ANSWER MUST BE IN 4 DECIMAL PLACES. - TELL THE DIRECTION AND WHETHER IT IS TENSILE OR COMPRESSION. - WRITE YOUR SOLUTION PROPERLY (EASY TO UNDERSTAND). - PLEASE BASE YOUR SOLUTIONS ON THE SAMPLE PROBLEM I'VE GIVEN.
Problem 3.25 The acrylic plastic rod is 200 mm long and 25 mm in diameter. Figure 1 of 1 -200 mm- Part A If an axial load P of 400 N is applied to it, determine the change in its length. Ep =2.70 GPa, vp = 0.4. (Figure 1) Express your answer with the appropriate units. 8 = Submit Part B μÃ Ad= Value Submit Incorrect; Try Again; 4 attempts remaining Units My Answers Give Up Determine the change in its diameter. Express your answer with the appropriate units. μA Value Units ? My Answers Give Up ?
- GET THE GIVEN, WHAT IS ASKED, AND THE ANSWER. - MAKE A PROPER FREE BODY DIAGRAM. (IT DOES HAVE THE GREATER POINTS IN THIS ACTIVITY) - YOUR SUB ANSWERS MUST BE IN 6 DECIMAL PLACES. - YOUR FINAL ANSWER MUST BE IN 4 DECIMAL PLACES. - TELL THE DIRECTION AND WHETHER IT IS TENSILE OR COMPRESSION. - WRITE YOUR SOLUTION PROPERLY (EASY TO UNDERSTAND). - PLEASE BASE YOUR SOLUTIONS ON THE SAMPLE PROBLEM I'VE GIVEN.