15.23 In the supply system shown in Fig. P15.23, the pressure required at the delivery end is60 psi. Determine (a) the pumping head, and (b) the power delivered by theConsider the entrance and exit losses and a water temperature of 70 F,pump.Figure P15.23Q= 0.8 cfsp= 60 psi50 ft10 ft15.24 A fire hydrant is supplied through three welded steel pipelines arranged in series. Thetotal drop in pressure due to friction in the pipeline is limited to 50 psi. What is the dis-charge through the hydrant? Disregard the minor losses.691Problems4-in, 1000 ft commercial steel

Answered: Image /qna-images/answer/c29042ef-9469-43ff-9d88-92e428384fc7.jpg

In the supply system shown in Fig. P15.23, the pressure required at the delivery end is 60 psi. Determine (a) the pumping head, and (b) the power delivered by the pump. Consider the entrance and exit losses and a water temperature of 70°F. Figure P15.23 Q = 0.8 cfs p= 60 psi 50 ft 10 ft pel pinelines arranged in series. The 4-in, 1000 ft commercial steel

In the supply system shown in Fig. P15.23, the pressure required at the delivery end is 60 psi. Determine (a) the pumping head, and (b) the power delivered by the pump. Consider the entrance and exit losses and a water temperature of 70°F. Figure P15.23 Q = 0.8 cfs p= 60 psi 50 ft 10 ft pel pinelines arranged in series. The 4-in, 1000 ft commercial steel

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

tank contains water upto a height of 1 m above the base. An immiscible liquid of sp. gr. 0.8 is filled on the top of water upto 1.5 m height. Calculate : () total pressure on one side of the tank, () the positiom of centre of pressure for one side of the tank, which is 3 m wide.
A Pump The oil tanks have a diameter of D = 12m. The initial depth of the oil in tank A is 20m, and in tank B the depth is 1 m. The pump delivers a constant head of 60 m. The connecting pipe has a diameter of b = 0.2m, and the head loss due to friction in the pipe is hyL = 8- Find the time required to fill tank B to 14m depth. (neglect minor losses)
I need the answer as soon as possible
i need the answer quickly
- Probl Water flows from a large open tank, through a valve and out a pipe to atmosphere. A-9 cm². Az = 11m. h₁ = 5V²/2g Find: I Discharge (Q=?) in pipe. Assumptions: a = 1.
height of water the pressure intensity : () at the interface of the two liquids, and (ii) at the bottom of the tank. [Ans. () 1.57 N/cm", (il) 3.04 N/em 6. An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of 2 m. Find 7. The diameters of a small piston and a large piston of a hydraulic jack are 2 cm and 10 cm respectively, A force of 60 N is applied on the small piston. Find the load lifted by the large piston, when: (a) the piston at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jackis [Ans. (a) 1500 N, (b) 1520.5 NJ kg given as 1000 - 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take [Ans. 1.962 N/cm? (gauge), 12.066 N/cm? (abs.)] - atmospheric pressure as 10.1043 N/cm?. 9. A simple manometer is used to measure the pressure of oil (sp. gr, = 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and left…
5-64. A thin rubber tube of 25 mm inside diameter is used to siphon water from the large tank of Figure 5.56. To prevent the tube from collapsing, the pressure inside the tube can not be less than 50% of the pressure outside the tube. Determine the smallest value of h to prevent the siphon from stopping due to collapsing of the tube. 2.5 m 5 m Figure 5.56 System for Exercise 5-64. THANK SUNTETICE Full Michifo Nas s itset SCH
Plss answer ASAP
Q1: Derie an epressin for the shear stress at the pipe wall when an incompressible faid flows draugh a pipe wnder pressure. Use dinmsional ana)sis witk the following siguißcant parameters: pipe diameter D, flow velociy V, and vicenity and density p of the fuid. Q2: : Use dinensional analysis to derive as epression for the power develaped by an engine in terms of the torque T and rotartive speed u.
Determine the resultant force of the water acting on the circular glass plate that Is to the side panel of the tank. Also, determine the location of the center of pressure along this inclined side, measured from the top. Question 2: FYw.h.A ate Fv= Yw.V 3 m radie 9810 Ixr x gate 9810 1 m 2 m Ma:0 Nar3- Fn 号×3-fvx3- -0 Ma=0-) NBx3- F t /2Fy-0 120° 3 m 1,- I,