In the structure shown, force F is applied at point A at anangle of e in the direction shown. Pins at G, E, D, B, andC are all frictionless and all members are weightless. Forthe given values of F and e determine:F= 100 N0 = 10 degAG(a) The reactions at points G and E(b) The forces applied to member GDC at points C and D(c) The forces applied to member ABC at point B70 m50 mED BNote: components of forces in x and y directions areenough.15 mYA60 m20m

Answered: Image /qna-images/answer/f0f57c30-50ab-431f-94d8-38ba90af9f70.jpg

In the structure shown, force F is applied at point A at an angle of 6 in the direction shown. Pins at G, E, D, B, and C are all frictionless and all members are weightless. For the given values of F and 0 determine: (a) The reactions at points G and E (b) The forces applied to member GDC at points Cand D (c) The forces applied to member ABC at point B Note: components of forces in x and y directions are enough. yA

In the structure shown, force F is applied at point A at an angle of 6 in the direction shown. Pins at G, E, D, B, and C are all frictionless and all members are weightless. For the given values of F and 0 determine: (a) The reactions at points G and E (b) The forces applied to member GDC at points Cand D (c) The forces applied to member ABC at point B Note: components of forces in x and y directions are enough. yA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Show detailed solution.
I need the answer as soon as possible
Homework: The pin-connected structure of Figure below has the 2400 N.mm moment applied to member CDE. Neglecting the weights of all members, determine the horizontal and vertical components of the pin reaction at E on member CDE. 200 Nimm 2400 N.mm 3 mm Smooth slot 50 Nimm B. 3 mm A 8 mm 2 mm 3 mm
In the following figure, a crank is supporting a mass m, is connected to a flexible cable, and supported on a pin at A. Check the correct option that corresponds to the reaction forces at A so that the structure remains in balance. Choose between A, B, C or D
The rectangular plate shown below weight 100lb. and is held in position by a cable EF and hinges at A and B. The hinge at B does not exert any axial thrust(Bx=0), and both hinges A and B do not exert any moment. Determine the tension in cable EF and the reactions at hinges A and B.
Statics, Find the magnitude of the horizontal and vertical components of the pin reactions at A, B, and E (Ax, Ay, Bx, By, Ex, Ey)
The Figure shown below is the truss patten proposed by engineering students for the one part of modern houses. Reaction forces for both pin A and roller F have already been calculated. a H D 12 f1 6 ft A, = 0 45° 45° F B E 6 It 6 ft 6 t 6 ft -- 6 f1 - A, = 3 k 3k 3k F, = 3k a) By using appropriate methods calculate all determinable forces in the members and define whether the members are in tension or compression. b) Is there any zero-force member? If no add 2 to get more stable design. c) As we know, the bridges of long structure tend to elongate under the impact of thermal stress. Which design should be preferred for this case, and why?
The given truss below is loaded vertically downward with 4KN and 8KN at points Cand D, respectively, as shown. A model of the truss was made in a laboratory, and it was found out that the values of internal forces in members A-L, A-B, and B-K are as indicated in the table. If the vertical reactions at A and G are 6.667 KN and 5.333 KN respectively, complete the table and answer the succeeding questions. Approximate all answers up to three decimal places. What is the behavior of the internal reaction of Member A-L?" 8 kN 4 kN B 3 m K J 1 H 12 m, 6 @ 2 m O tension O compression O none of the choices оо
F= 150 N In the structure shown, force F is applied at point A at an angle of 0 in the direction shown. Pins at G, E, D, B, and C are all frictionless and all members are weightless. For the given values of F and 0 determine: F 0 = 40 deg A G (a) The reactions at points G and E (b) The forces applied to member GDC at points C and D (c) The forces applied to member ABC at point B 70 m 50 m E D B Note: components of forces in x and y directions are enough. 15 m YA 60 m 20m ALL WORK MUST BE SHOWN (FBDS, EQUATIONS, etc.). CORRECT ANSWERS WITHOUT CLEAR EVIDENCE OF HOW THEY WERE OBTAINED WILL BE MARKED AS ZERO.
show complete solution, final answer should be in two decimal only, i will automatically give upvote.
Figure b shows a truss structure in static equilibrium that is simply supported at A and C. Calculate the reaction forces RA and RC when subjected to vertical loads of 50 kN, 25 kN and 15 kN at nodes D, E & C, respectively.
is supported at the left end 6-86 Beam CD of Fig. C by a smooth pin and bracket and at the right end D by a continuous cable that passes around a frictionless pulley. The lines of action of the force in the cable pass through point D. Determine the components of the reaction at sup- port C and the force in the cable when a 5-kN load W is be- ing supported by the beam. 2 m 2 m A D 3 m 4 m 4 m.