In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining Band D, determine the allowable load P if an overall factor of safety of 2.6 is desired. Top view 8 mm. A -200 mm- B DO -180 mm- The allowable load P is 20 mm Front view 12 mm C P KN. t 8 mm- 4. 12 mm. 1 B -8 mm D the Side view

In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining Band D, determine the allowable load P if an overall factor of safety of 2.6 is desired. Top view 8 mm. A -200 mm- B DO -180 mm- The allowable load P is 20 mm Front view 12 mm C P KN. t 8 mm- 4. 12 mm. 1 B -8 mm D the Side view

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

w=15
A tennis ball is thrown into the air with initial speed vo=98 m/s and angle (theta) 10 degrees from the ground. Find the distance it travels (x) when it hits the ground? Also find the average speed, and average velocity.
PROBLEM 1 Determine the allowable weight that the assembly can handle if the cable AB has a working stress of 200 Mpa and cable AC has a working stress of 150 Mpa. The cable cross sectional areas are 300 mm? for cable AB and 330 mm2 for cable AC. B 50° 28° A W
For the clevis connection shown, the shear stress in the 0.48-in.-diameter bolt must be limited to 29 ksi. Determine the maximum load P that may be applied to the connection. clevis Answer: P = i 1345.2 kip.
Determine the largest axial load P that can be safely supported by a flat steel bar consisting of two portions, both 10 mm thick and, respectively, 40 and 80 mm wide, connected by fillets of radius r=4 mm. Assume an allowable normal stress of 180 MPa.
Link AC is made of a steel with a 65-ksi ultimate normal stress and has a xin. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter pins, while member BCD is connected to its support at B by a -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.75 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. 16 IN 8 in 16. ---4 in- The largest load P that can be applied at Dis[ lb.
A14-kN tensile load will be applied to a 50-m length of steel wire with E = 200 GPa. Determine the smallest diameter wire that can be used, knowing that the normal stress must not exceed 150 MPa and that the increase in length of the wire must not exceed 25 mm. The smallest diameter that can be used is ___mm?
A set of 10 bolts is to be used to provide a clamping force of 50000 lb between two components of a machine. The load is shared equally among the 4 bolts. Knowing that the grade of the material is SAE Grade 4, if each is to be stressed to 90 %of its proof strength. Then the required tensile stress area is: Select one: A. A, = 0.0714 in В. B. A, = 0.22 in %3D 2. C. A, = 0.0865 in 2. D. A, = 0.0855 in
only HANDWRITTEN answer needed ( NOT TYPED)
For the connection shown, the average shear stress in the 17-mm-diameter bolts must be limited to 260 MPa. Determine the maximum load P that may be applied to the connection. 296 KN 354 KN 444 KN 479 KN 326 kN
Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing that the maximum allowable tensile stress in the glued splice is 82.4 psi, determine the largest load P that can be safely supported if W = 4.5 in, L = 8.9 in and θ= 55.3