In the simply supported beam, the uniformly distributed loads (in kN/m) along with the two applied couples (in kN.m) are expressed in terms of W as shown below. Find the value of W to reach a maximum bending moment of Mmax 173.333 kN.m in the beam. 3W 2W W 3W

In the simply supported beam, the uniformly distributed loads (in kN/m) along with the two applied couples (in kN.m) are expressed in terms of W as shown below. Find the value of W to reach a maximum bending moment of Mmax 173.333 kN.m in the beam. 3W 2W W 3W

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15900 ksi] rods, and a solid steel [E = 30300 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.69 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.42 in. Assume L=37 in and L2=68 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 28 kips is applied. (1) L2 (1) B P. Answers: i 27.744 ksi. 02 = 4.512 ksi.
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15,000 ksi] rods, and a solid steel [E = 30,000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.500 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.360 in. If all bars are unstressed before the load P is applied, determine the normal force in steel rod (2) after a load of P = 36 kips is applied.
Consider the continuous beam as shown in figure below: RA 9,- 2 6 (m) R₂ What will be the magnitude of slope at B? H₂ 6 (m) Re
According to σgüv= 700N/cm2 and tgüv = 100 N/cm2 in the material of the output beam given the loading condition, cross-section and dimensions in the figure; a) Find the largest Q-spread load that can be safely transported. b) Draw a diagram of shear stress in cross-section. (Note: for all odd values, two digits will be taken after the point.)
A beam 2.4 m long is simply supported at two points A and B which are 1.44 m apart; point A is 0.36 m from the left-hand end of the beam and point B is 0.6 m from the right-hand end; the value of EI for the beam is 240×10® Nmm². Find the slope at the supports due to a load of 2 kN applied at the mid-point of AB. Use the reciprocal theorem in conjunction with the above result to find the deflection at the mid-point of AB due to loads of 3 kN applied at each end of the beam. Ans. 0.011, 15.8 mm.
Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of 4=200 mm'. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. FEA 3m rigid B A 2m 1.5m
I need the answer as soon as possible
The slope of the shear diagram is equal to Select one: a. Rotational moment b. Distributed load intensity С. Bending moment d. Total weight
The compound beam is subjected to a uniform dead load of 380 lb/ft and a uniform live load of 285 lb/ft. Assume B is a pin and C is a roller. Follow the sign convention. (Figure 1) Figure A 5 ft 00 B 5 ft D 5 ft C 1 of 1 Part A Determine the negative bending moment at A with the maximum magnitude. Express your answer using three significant figures. ΠΑΣΦ (MA)max(-) = Submit Part B (VD) max(+) Request Answer Determine the maximum positive shear at D. Express your answer using three significant figures. Submit = ΑΣΦ ↓↑ vec Request Answer vec ? ? k.ft lb
Q1: A simply supported beam and its cross section are shown in Figure. The beam carries a load of (10 kN) as shown. Its self-weight is (3.5 kN/m). Calculate the maximum bending stress at X- X. 3.5 kN/m 1.2 m B 1 10 kN 1.2 m 1.2 m 3.6 m 100 T 150 mm Hole T 300 200 200 --
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 14800 ksi] rods, and a solid steel [E = 32200 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.68 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.54 in. Assume L1=50 in and L2=81 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 21 kips is applied. (2) (1) L2 (1) |L1 B P.
1.8