In the parallel capacitor turn-off circuit of Fig. 1.38(a), the battery has a voltage of 68 V, the load resistance is 5 2, and the value of the capacitance just required for turn-off is 11.43 µF. Estimate the turn-off time of the load thyristor. Also, sketch the waveforms of v™h, , ic, and ve with values also noted therein. Ans. 40 µs The auvi tn off aironit fellowina doto:

In the parallel capacitor turn-off circuit of Fig. 1.38(a), the battery has a voltage of 68 V, the load resistance is 5 2, and the value of the capacitance just required for turn-off is 11.43 µF. Estimate the turn-off time of the load thyristor. Also, sketch the waveforms of v™h, , ic, and ve with values also noted therein. Ans. 40 µs The auvi tn off aironit fellowina doto:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Cyclic Voltammetry and Charge-discharge The given figure is the Galvanostatic Charge-discharge curves of a supercapacitor made with MnO2 coated on a CNT electrode. Potential is measured with respect to time by applying different current densities. Based on the plot, answer the following questions 4. Is it possible to estimate maximum power of the device with this charge-discharge curve? If possible, explain how you would do it. (calculation is not necessary)
I. SOLVE THE FOLLONING PROBLENS : A COPPER WIRE OF 0,3 Mm RAAUS HAS A LEN ETH OF 1. JOM- IF THE RESISTIVITY of cOpPER IS 1-7 x0 WHAT WOULD BE THE RESISTANOE OF THE WIRE? OF A 100m WIRE IS 1035 mm AND 3.7 OHMS. WHAT 2. THE DIAMETER THE REISTANCE IS IS THE CONDUCTIVITY 3. WHAT WILL BE THE VALUE OF A CAPACITOR WHEN IT HAS A CAPACITIVE REACTANCE OF 300R ANP to A 6o HZ. SUPPLY? IN FARADS IS CONNECTED 4. WHAT Is THE VALUE OF THE RESISTOR WITH THE FOLLOWING COLORS ? A. BROWN, BLACK, GOLD, REP B. BLUE YELON BROWN, SILVER PED, SILVER, BROWN, VIOET C. 5. AND t WHEN V 220V AND R= 50n WHEN I = 45 A WHEN V = 120V FIND V ANO R 80n AND AND E= 11A-
a) A single-phase uncontrolled bridge rectifier supplies a highly inductive load from a single- phase 50 Hz AC voltage source. By neglecting the effect of line inductance, the rectifier generates average output voltage and current values of 180 V and 6 A, respectively. Due to the highly inductive load, the current waveform is constant and ripple-free. However, when considering a line inductor of 5 mH, the average output current drops by 3%. i) With an aid of a circuit diagram, explain the reason behind the zero voltage across the rectifier's output during the commutation interval. ii) Calculate the commutation angle and the average voltage drop values.
Consider the full wave rectifier circuit shown below, with a large smoothing capacitance C = 300µF placed in parallel with the load resistor RL = 1KN and Vm = 15V. Assume that the diodes are piece-wise linear with r,= 100 and V, 0.7V then derive the plot for the output voltage across the load resistor RL. Plot A V Plot C V wm Plot B V Plot D V please pick a plot
⦁ Consider the below zener diode circuit and find the values of , , , . Use the constant voltage drop model which is shown is Figure 2. Show your solution steps clearly and explain them. The answers without solution steps will not be graded. Also, state your results in the sections below the circuits. ( = 0.1 )
Please show all work, thank you :)
A 1N4748A zener diode has a ZZ of 23 Ω. Taking the data from the datasheet VZ = 22 V with a test current, IZ, of 11.5 mA. What is the voltage across the zener terminals when the current is 6 mA? When the current is 20 mA? Make the representation of the values by means of their curve characteristic.
?
Please solve this question queckly
Consider the following circuit with Vs(t) = 2.0 + 0.02 sin(2 pi t) V,R1 = R2 = 25ohms Idc = 1mA, Vdc = 5V. Assume Vy = 0.7V and VT = 25mV.a) Draw the equivalent circuit under DCb) Determine the DC voltage and current through the diode.c) Draw the equivalent circuit under acd) Determine the total current through the diode
A single-phase bridge type full-wave uncontrolled rectifier is connected to a voltage source and has an RL load at its output. The RL load satisfies the (L/ R) >T condition. In this case, the output current of the rectifier is 10 A pure direct current. Voltage source impedance consists of inductance only and its value is 3 mH. The function of the voltage source Vs (t) below are given. Vs (t) = 311sin (2n50t) V Note: T=0.02s is the period value of the voltage source. R and L values do not matt er in solving the problem. a. What is the value of the overlap angle in radians? b. Find the effective value of the output voltage.
Please Help will upvote...thanks