A single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source is connected to an inductiveload. The general expression of the RMS AC component of the current is given below where Vm is themaximum input voltage. If R = 1k2, then the value of the inductance that would limit the AC component IAc toless than 5% of the DC component Ipc would be equal to:4VmIACV2. 1. R2 + (2wL)?Select one:O a. 4.92HOb. 11.92HO c. 8.92HO d. 14.92HTOSHIBA24

Answered: Image /qna-images/answer/393c032d-6b6a-46d7-bc1a-a7ea75c1c0ba.jpg

A single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source is connected to an inductive load. The general expression of the RMS AC component of the current is given below where Vm is the maximum input voltage. If R = 1kQ, then the value of the inductance that would limit the AC component IAc to less than 5% of the DC component Ipc Would be equal to: 4Vm IAC = V2. Tt. VR2 + (2@L)²

A single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source is connected to an inductive load. The general expression of the RMS AC component of the current is given below where Vm is the maximum input voltage. If R = 1kQ, then the value of the inductance that would limit the AC component IAc to less than 5% of the DC component Ipc Would be equal to: 4Vm IAC = V2. Tt. VR2 + (2@L)²

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

need quick solution please
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di i v2 = VmSin ot RL Vs(N V1 Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V None of the above ell ell
The input to a full-wave rectifier is 20 V AC (RMS). The load resistor is 20 ohms and rectifier losses are 4W. The ripple factor of the rectifier is: O A. 0.96 OB. 0.33 O C. 0.48 O D. None of the other choices are correct O E. 0.75
/1/A single-phase, half-wave, controlled has a source 220V at 50 HZ and is eding a load R=2002 and L=25 mH, the firing angle a=60° and the current tinction angle ß=225° Determine the average load voltage and current. O Determine the rms load voltage and current. led rectifier the value of the output
Vi (t) = 10.sinwt Does not pass positive alternans when Volt input voltage is applied, only Design and explain two different circuits that pass negative alternans. Draw the input and output voltages. What are the types of these circuits? (Note: You can use the ideal diode approach)
INCLUDE ALL THE DECIMALS.
The ripple factor for pure dc is Answer: For the given circuit below, it operates on a peak-to-peak input voltage of 390.1 V, F= 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1, D2 AC Input Vsec (Source) .03 D4 Load O 27.31 O 18.11 O 13.93 O 20.91
(01) AC Diode circuits. (Course: Electronic Devices and Circuit Theory) -Redraw the circuit, Assume diodes are off and Redraw, Apply KVL. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.
The average (DC) value of a half-wave rectified voltage with a peak value of 200 V is: a. 63.7 V b. 127.3 V c. d. OV 141 V 2. Voltage regulation is determined by: a. load current b. Zener current and load current c. changes in load resistance and output voltage d. changes in no-load voltage and full-load voltage When a 60-Hz sinusoidal voltage is applied to the input of a full-wave rectifier, the output frequency is: a. 120 Hz b. 60 Hz c. 240 Hz d. 0 Hz