In the MOSFET circuit shown, the transistor hasV = 1.0 V, k = 20 µA/V, L=4 µm, W =100 µm and i = 0.Find the drain current Ip and the voltage V, State in what region of its characteristics the MOSFET operates (i.e. triode,saturation, cutoff).+5 VR- 4 k2-5 V

Here the figure shows source follower circuit to calculate ID , first we have to know the region of…

In the MOSFET circuit shown, the transistor has V= 1.0 V, k = 20 µAN, L=4 um, W = 100 µm and i=0. Find the drain current Ip and the voltage Vs State in what region of its characteristics the MOSFET operates (i.e. triode, saturation, cutoff). +5 V V R=4 k2 -5 V

In the MOSFET circuit shown, the transistor has V= 1.0 V, k = 20 µAN, L=4 um, W = 100 µm and i=0. Find the drain current Ip and the voltage Vs State in what region of its characteristics the MOSFET operates (i.e. triode, saturation, cutoff). +5 V V R=4 k2 -5 V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

04:- Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE = 10 V. Use standard valued 5% resistors and draw a schematic diagram of your design. (10 points)
Determine the VDS and the drain current for the E-MOSFET circuit shown. The data sheet for this particular MOSFET gives ID(ON)=500 mA at VGS=10 V and VGS(th)=1 V.
Figure 1 shows the typical output characteristics of MOSFET. Those characteristics show the difference curve of the drain current, Ip, as function of the drain- source voltage, VDs at a given gate-source voltage, VGs. In the Figure 1, it shows that the Ohmic region. What the meaning of the Ohmic region? Explain with necessary example any consequences that will happen for any condition of MOSFET. 360 10 V ev 7V 320 280 Ohmic region + 240 200 160 120 5.5 V- 80 40 2 3 Vos [V] Figure 1 lo [A]
An n-channel silicon MOSFET has the following parameters: W = 6 µm, L = 1.5 µm, and tox = 8 nm. When the transistor is biased in the saturation region, the drain current is Ipsat = 0.132 mA at 1.25 V. Determine the electron mobility and the VGS 1.0 V and Ipsat 0.295 mA at VGS threshold voltage.
A 4.7 zener diode is connected to the base resistor. The left side of the resistor sits at about 12V. The right side of the biasing resistor is connected to the Zener and npn transistor. The Zener bias is 5mA. The base current needed is 80uA. What is the appropriate resistor for this circuit? (In kohms) I
a) Figure B3 shows a cross section for a Metal Oxide Semiconductor Field Effect Transistor (MOSFET) in diagrammatic form. (i) (ii) Sketch the energy band diagram for the MOSFET along the line X-Y shown in Figure B3 when bias voltages are applied such that the silicon surface is inverted. Label all important features of your sketch and state any assumptions made. Sketch a box plot showing the charges present in the structure when the silicon surface is inverted. Indicate the source of all the charges and state whether they are positive or negative. Source n+ Metal Silicon Substrate - p X dioxide Drain n*
Determine vo versus v₁ for the circuit shown in Figure 2. Assume that the MOSFET operates in saturation and is characterized by the parameters K and VT. Vs R₁ www Figure 2 wwww RL R₂ wwwww VO Note: assuming the MOSFET works at normal saturation regime and ips= (VDS -VT)²2 K 2
Determine in which mode (depletion, enhancement or neither) each D-MOSFET in the figure below.
Q2 Design a voltage divider bias circuit for an npn silicon transistor having B %D 100 to be used in a Common Emitter configuration. The quiescent point = 1 mA, VCE = 5 V. The supply voltage (Vcc) is 15 V. (Q point) is to be l. Assume VĘ = 0.1Vcc and BRĘ 2 10R2. (a)Find all the resistors values and draw the schematic diagram of this Common Emitter Amplifier with bypass capacitor CE.
Q1) Answer True or False for the following: 1- Field-effect transistors are Bipolar devices. 2- A depletion MOSFET (D-MOSFET) can operate with a zero, positive, or negative gate-to source voltage. 3- The 4-layer diode is a thyristor that conducts when the voltage across its terminals exceeds the breakover potential. 4- The benefit of SCR Crowbar is power amplification. 5- Most op-amps require only a positive dc supply voltage.
7. MOSFET circuit The MOSFET in the circuit below has V, = 1 V and kn = 4 mA/V². a) Is the MOSFET operating in saturation or in the triode region? b) Determine the drain current Ip and Vout: + 5 V 5 k Vout
2. We discussed in class how the channel capacitance can be modeled in different region of operations in MOSFETs. For your reference, the slide is shown below. Explain how you think the model would look like if a transistor is in velocity saturation region? Channel Capacitances Channel capacitance is a voltage dependent and non-linear capacitance S C P-sub Bulk Cutoff Region D Operation Region Cutoff Linear Saturation S P-sub Bulk C Linear Region CGBCH CoxWLeff 0 0 1 2 3 S P-sub Bulk Saturation Region CGSCH 0 сат CoxWL eff 1 2 CGDCH 0 CoxWLoft CoxWLoff eff D 0