In the hanger shown in figure 2, the upper portion of link ABC is 3/8 in. thick and the lower portions are each 1/4 in. thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 3/8-in. diameter while a 1/4-in.-diameter pin is used at C. Determine: a. the shearing stress in pin A. b. the shearing stress in pin C. c. the largest normal stress in link ABC. Figure 2 1.75 in. 6 in. 7 in. 500 lb 5 in. D 1.25 in. 10 in.

In the hanger shown in figure 2, the upper portion of link ABC is 3/8 in. thick and the lower portions are each 1/4 in. thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 3/8-in. diameter while a 1/4-in.-diameter pin is used at C. Determine: a. the shearing stress in pin A. b. the shearing stress in pin C. c. the largest normal stress in link ABC. Figure 2 1.75 in. 6 in. 7 in. 500 lb 5 in. D 1.25 in. 10 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 16 The assembly shown supports a distributed load of w = 0.8 kip/ft. The pins at A and B are 0.4" in diameter and the rod has a ½" diameter. The yield strength of the pin in shear is 25 ksi and the rod's tensile yield strength is 38 ksi. a. b. Calculate the factor of safety with respect to yielding in the rod. C. Calculate the force in rod AB. Don't forget to draw a FBD! e. Calculate the factor of safety with respect to yielding for the pins. d. What value would you report as the final factor of safety for the structure? Explain your answer. Pin at B 3 ft B 4 ft Pin at A 2 ft If the rod is made of structural steel (E = 29,000 ksi, v = 0.33), calculate the final diameter of rod AB. W
None
A cantilever is to be attached to the flat side of a 6-in wide channel used as a column. The cantilever is to carry a load as shown in the figure. If two fasteners are used, should the array be arranged vertically, horizontally, or diagonally? How would you decide? Specify an optimal bolt pattern and size the bolts. 6 in- 6 in 6 in -in steel plate + 2000 lbf
M16 x 2.0 ISO 5.8 coarse series bolts and nuts clamp a 26-mm-thick steel cover plate to a 6-mm-thick steel flange. Steel washers (Size: 16R) are used under the head of the bolt and also under the nut . Assume E = 207 GPa- (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (c) Determine the stiffness of the members. (d) Determine the stiffness of the joint.
None
Solve correctly
Bolts distributed about a bolt circle are often called upon to resist an external bending moment as shown in the figure. The external moment is 19 kip-in and the bolt circle has a diameter of 15 in. The neutral axis for bending is a diameter of the bolt circle. What needs to be determined is the most severe external load seen by a bolt in the assembly. M Neutral axis R NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. View the effect of the bolts as placing a line load around the bolt circle whose intensity FÅ, in pounds per inch, varies linearly with the distance from the neutral axis according to the relation Fb Fb,max R sin 8. The load on any particular bolt can be viewed as the effect of the line load over the arc associated with the bolt. For example, there are 12 bolts shown in the figure. Thus, each bolt load is assumed to be distributed on a 30° arc of the bolt circle. Under these conditions, what is the largest bolt…
Need correctly in neat and clean handwritten solution
* Required For nos. 38-40, satisfy the conditions of the given problem below: The internal drag truss of the wing of a light airplane is subjected to the forces shown in Determine the force in figure 3. each member, and state if the members are in tension or compression. 38. Load on member BC * 1 point H 0.61 m 0.61 m- 0.61 m 356 N O A. 579.23 N (T) B. 579.32 (C) O C. 580.20 N(T) D. 580.20 N (C) 356 N 0.61 m -0.46 m- 267 N 178 N
Assignment 2 A Copper bar is loaded as shown complete the following: a. Draw a neat shear force and bending moment (Table of values is required) b. Calculate the maximum bending stress, clearly indicate where this occurs c. Calculate the maximum shear stress, clearly indicate where this occurs d. Plot the bending and shear stress for the cross section at x= 4 ft. from the left hand support. Clearly show the calculations were made at the following positions: y-0, 2, 4, 6, 8, 10 and 12 35 Ib/ft. 200 Ib Beam cross section 12 65" 8 ft. 5ft. 3 ft.
Determine the distance x bar for the problem in example ?
Urgent