In the given figure the pipe entrance is sharp-edged. There is threaded globe valve. If the flow rate is 0.004 m3/s, what power, in W, is extracted by the turbine if the turbine efficiency is = 81.9 %? Take p = 998 kg/m3 and u = 0.001 kg/m-s. Open globe valve Turbine 40 m Water Cast iron: L-125 m, D=5 cm

In the given figure the pipe entrance is sharp-edged. There is threaded globe valve. If the flow rate is 0.004 m3/s, what power, in W, is extracted by the turbine if the turbine efficiency is = 81.9 %? Take p = 998 kg/m3 and u = 0.001 kg/m-s. Open globe valve Turbine 40 m Water Cast iron: L-125 m, D=5 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pcton-turbine develops 5MW power at a specific spced of 15. Thc water is supplied through a pipeline from a reservoir the level of which is 300m above the nozzles. Assuming for a friction loss in the pensto ck pip eline to be 5% of the gross head. The turbine speed is rpm
Read the question carefully and give me right solution according to the question
A flow rate of 3 m'/s of water is available at a height of I 10 m at a project site. Due to losses in the sup- ply line, the head available at the inlet to powerhouse is estimated to be only 101 m of water. The leakage losses in the powerhouse are negligible. Mechanical losses account for 150 kW. Frictional losses in the rotor blades may be taken as 250 kW. The exit velocity of water from the turbines is 4.5 m/s. Calculate the hydraulic, mechanical, and overall efficiencies of the plant. The specific weight of water may be taken as 9810 N/m.
short and simple ,Do fast.
Q3/ A Francis turbine has runner radii: ₁ = 0.3m, r2 = 0.2m & operates under the following conditions:- Q = 0.035 m³/sec, 0o = 15 rad/ sec, a₁ = 60°, a₂= 30°, V₁= 10 m/sec, V₂= 6 m/sec, and its efficiency is 85%. Find: 1- The head required? 2- Inlet vane angle? 3- Runner thickness at inlet?
Example -5.2- It is required to pump cooling water from storage pond to a condenser in a process plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d. pipe is available and the pump has the characteristics given below. The head loss in the condenser is equivalent to 16 velocity heads based on the flow in the 74.2 mm pipe. If the friction factor = 0.003, estimate the rate of flow and the power to be supplied to the pump assuming n = 0.5 Q (m³/s) 0.0028 0.0039 0.005 0.0056 0.0059 Ah (m) 23.2 21.3 18.9 15.2 11.0
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
Complete soln and correct units pls. Thanks ?
A hydraulic vane pump running at 1800 rpm develops 2 L/s flow at 750kPa. Volumetric efficiency is .85 and overall efficiency is 0.8. Determine the Theoretical Flow Rate, QT. O 0.00235 m³/s O 0.0025 m³/s O 0.0027 m³/s O 0.0017 m³/s
4. Water (p = 1000 kg/m³) is transferred from a large lake to an open storage tank located at elevation as shown in the Figure 2 below at a flowrate of 90m³/hr. The losses through pipe and fittings (hL) is given as 8m. Determine the mechanical efficiency of the pump if the shaft power required is 12kW. State the assumptions made in your calculations. 30 m WaterLevel Pump Centre Figure 2 Tank
Energy balance. The flow rate of water is 0.021 m'/s through a 355-m long, 11-cm-diameter pipe (shown below and not to scale). The turbine that has an efficiency of 82% is used to recover the potential energy and generate power. Both reservoirs are very very large and contain water at 8°C. The roughness of the galvanized iron pipe is 0.14 mm. Problem 2 105 m 42 m What is the turbine output, i.e., how much usable power can obtained from the turbine?
A centrifugal pump is used to pump a liquid with the properties given below. Liquid is pumped from a storage tank at 95 kPa (a) to a discharge tank at 300 kPa (a). The system configuration is given in the table below. Table 1: system configuration Suction Discharge 4 50 Length (m) Diameter (m) 0.07 0.055 12 90° bends (L/D-35) 5 T piece (L/D=7) Gate valve (L/D-35) 1 1 1 2 Static height (m) 25 Liquid density = 1100 kg.m³ Viscosity = 1.5 x 10-³ Pa.s Vapour pressure of the liquid = 25 kPa (a) Material of construction of pipe is commercial steel, ε = 000045 m Table 2: Pump data 0 10 20 30 40 Flowrate (m³.hr¹) Head (m) 55 56 51 36 6 NPSH (m) 0 2 6 11 19 22 3.1. Graphically determine the optimal operating point of the pump in the above system using the pump data in Table 2. 3.2. Determine the NPSH of the system and determine whether the pump will cavitate when used in the above system.