Answered: In the given figure, determine the… | bartleby

Related questions

Question

In the given figure, determine the magnitude of the force F that makes the rod in
equilibrium, given that the magnitude of the given force is 7 N and cos0=4/5.
30
2.1 m
A
4.7 m
e
F

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A person pushing a uniformly‑loaded 51.7 kg51.7 kg wheelbarrow of length ?L with pushing force ?⃗ P→ is attempting to get it over a step. The maximum horizontal force that the person can apply is ??=681 N.Px=681 N. What is the maximum height ℎh of the step, expressed as a fraction ?n of the wheel's radius ?R, that the person can get the wheelbarrow over? The gravitational acceleration is ?=9.81 m/s2.
The drawing shows an A-shaped ladder. Both sides of the ladder are equal in length. This ladder is standing on a frictionless horizontal surface, and only the crossbar (which has a negligible mass) of the "A" keeps the ladder from collapsing. The ladder is uniform and has a mass of 19.8 kg. Determine the tension in the crossbar of the ladder. 30.0 4.00 m Crossbar 1.00 m Number Units the tolerance is +/-2%
A uniform rod weighing 15 kg is supported in a horizontal position by a pin and wire as shown in the figure. What is the magnitude of the tension in the wire?
If the new center of gravity of a 14 m uniform steel rod with a mass m = 75 kg is situated to the left of its geometric center after a 50 kg object is attached to it, determine the point where the object is attached. 4.5 m O 8.5 m 9.5 m 7.0 m
The figure below shows a horizontal rod, of length 6.4 m, with forces acting on it. A 30 N force acts at its left end, point O, in a direction down and to the left, 45° below horizontal. A 25 N force acts at its center, point C, in a direction up and to the right, 30° to the right of vertical. A 20 N force acts at the right end, in a direction down and to the right, 20° below horizontal.
You set up a Halloween prank by attaching a small board to a hinge above your front door. The far end of the board is held up by a cable that can be released by remote control. You place a spooky spider on the board that is dropped on unsuspecting trick-or-treaters when you release the cable. The drawing below shows the set-up. cable 40° Hinge 60 ст You use a board that is 60 cm long and the cable makes an angle of 40 degrees with the board when the board is held horizontally. You place the spider a distance of r = 37 cm from the hinge. The board has a mass of 2.2 kg and the spider has a mass of 1.6 kg. The hinge applies both a horizontal force and a vertical force. You will be asked to determine the direction of both of these forces (left, right, up, down). What is the magnitude of the tension in the cable in Newtons? T = What is the magnitude and direction of the horizontal force from the hinge? Enter a positive number for the magnitude. Fh = Direction ---Select--- What is the…
A flagpole has a uniform mass density and total mass of M and length L. It is hinged at the ground and makes an angle of U with respect to the horizontal, as shown. To support the pole, a horizontal cable is attached to the pole at a point L from the bottom of the pole. 3 What is the correct sum of torque equation for the axis perpendicular to the page and passing through the bottom of the pole? cable 2L/3 0-Mg + 흙LT=0 O-Mgcos0 +LTsin0 = 0 ○ 들Mgsind + 능TCOS6) +Tcose = 0 Mgsino + LTcos0 = 0 O- Mgsin0+LTcos0 = 0
a D1 Sign Dz A 2.20kg pole is attached to a wall with a hinge as shown. A 5.70kg sign is suspended at the other end of a pole, where D, = 3.30m. A cable attached to the wall forms an angle a = 18.0° with the wall, and is attached to the pole a distance D, = 1.40m from the hinge. Assume the origin is at the hinge. What is the torque on
3. A person holds a 10.0 kg lead ball in his hand, a distance of 32.0 cm from the elbow joint, as shown. The biceps, attached at a distance of 2.5 cm from the elbow, exerts an upward force on the forearm. Consider the forearm and hand to be a uniform rod with a mass of 1.50 kg. Calculate the force provided by the biceps muscle in order to hold the arm horizontally as shown. Use the elbow joint as the pivot point. Biceps 32 cm 2.5 cm
The top of the folding workbench has a mass of 36 kg with mass center at G. Calculate the magnitude of the force supported by the pin at E. 225 mm D G Answers: E = F E 670 mm 1000 mm H i N B 805 mm
(a) A person opens a 1.20 m wide door by pushing on it with a force of 57.5 N applied at the center of the door, at an angle perpendicular to the door's surface. What magnitude of torque (in N · m) is applied about an axis through the hinges? _________N · m (b) A man opens the same door, using the same force, again directed perpendicular to the surface, but now the force is applied at the edge of the door. What magnitude of torque (in N · m) is applied about the axis through the hinges now? _________N · m
Sl units of bending moment is kN^2 O kN.m km O kN

SEE MORE QUESTIONS