In the given 20.0 meter slab and inclined 10 with the horizontal, the ends are resting on inclines of 35° incline at B and 25° at A, a semi-trailer truck is to pass through it with the wheel loads as shown. How Far (x, meters) shall be the front wheels located before motion impends, the angle of friction is 15 ° for all areas of contact. If the weight of the slab is to be neglected 15.00 m 20 KN 16 KN 12KN 8 KN 3.6 m 4.0 m 1.2m 15° 20° 100

In the given 20.0 meter slab and inclined 10 with the horizontal, the ends are resting on inclines of 35° incline at B and 25° at A, a semi-trailer truck is to pass through it with the wheel loads as shown. How Far (x, meters) shall be the front wheels located before motion impends, the angle of friction is 15 ° for all areas of contact. If the weight of the slab is to be neglected 15.00 m 20 KN 16 KN 12KN 8 KN 3.6 m 4.0 m 1.2m 15° 20° 100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Compute the design and allowable compressive strength of a 12 meter built-up column composed of a steel plate with an attached channel section on each side. The web of both channel bars are welded to the steel plate, with their local x-axes coinciding with that of the steel plate. The thickness of the plate is 6 mm, with its width equal to the depth of the larger channel section. Assume that the column has fixed ends and is supported about the weaker at middle thirds, and about the stronger axis at mid-height. Assume all steel used are A36 steel. Properties of the Channel Sections C310 x 31 A d b t Ix ly 3930 mm² 305 mm 7.16 mm 74.7 mm 12.7 mm 53.7 x 10 mm 1.61 x 10 mm C 250 x 23 A d tw b t lx ly 2900 mm² 254 mm 6.10 mm 66 mm 11.1 mm 28.1 x 10 mm 0.949 x 10 mm
For a concrete-filled composite column Steel: Square Hollow section 350x350x16, f, = 450N/mm? Concrete: Grade 32 No reinforcement Effective length = 9.0m Determine a) Draw the Interaction Curve for x-axis
Design a one-way slab having a simple span of 3m. The slab is to carry a uniform live load of 7,500 Pa. Assume f°c = 27.6 MPa and fy= 276 MPa for main and temperature bars. Use 23.5kN/m3, 12 mm for main bars and 10 mm for temp bars.
D1
b10
3. For the cantilever concrete retaining wall shown below, determine the factor of safety against overturning if the angle of internal friction for the soil is 30 the coefficient of friction between concrete and soil is 0.45, and the unit weight of soil is 125 pcf. 1¹0 - 1' 0" MIEHELL 16' 1112 111년 111즈케호. 1'0" -6' 3"- 18" 1'6" 113/17 1112/111 - -3' 9". $ 1' 6"h 11' 6"-
What force is required to punch a 20-mm-diameter hole in a plate that is 22 mm thick? The shear strength of the plate is 340 MN/m2. Select the correct response: 587.48 kN 106.81 kN 129.25 kN 469.98 kN
Q3). Calculate the cross section area of cut and fill for the followings: St. 1) h= 2m cut at center line, s left = 5, and s right = - 3 St. 2) h = 0.6m fill at center line, s left = 9, and s right=7 St. 3) h=0 at center line, s left =-6, and s right - 10. (bo= 10 m, n = 1 in cut, and n = 2 in fill) for all sections.
The design specifications of a 1.2-m-long solid circular transmission shaft require that the angle of twist of the shaft not exceed 4° when a torque of 750 N-m is applied. Determine the required diameter of the shaft, knowing that the shaft is made of a steel with an allowable shearing stress of 90 MPa and a modulus of rigidity of 77.2 GPa. The required diameter of the shaft is mm.
I need the answer as soon as possible
Problem Given: • cantilever beam, fixed support at A • W = 15 kN/m • L=6m . El = constant Determine the following: 1. deflection at B 2. slope at B 3. deflection at midspan W L