In the FM system, the audio frequency is 1 KHz and the audio voltage is 2v. The frequency deviation is 4 KHz. If the audio voltage increase to 8 volt and audio frequency dropped to 500 Hz. Find the modulation index in each case and bandwidth using Carson's rule.

In the FM system, the audio frequency is 1 KHz and the audio voltage is 2v. The frequency deviation is 4 KHz. If the audio voltage increase to 8 volt and audio frequency dropped to 500 Hz. Find the modulation index in each case and bandwidth using Carson's rule.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Can you finish the Background including a synopsis of the relevant information of this this example "electrical maintenance and repair" And please cite an article or paraphrase of author. Thank you! The electrical wiring and electrical devices in the houses that are installed may have failure so the inspection is designed to definitely perform the clear capabilities. These electrical devices are...
Complete solution otherwise skip. Plxxx.
What is ampere circuital law?
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
b) Remove the following complements using DeMorgan's theorems. ______________________ ___________________ _____________ P+ Q + (C+D.E'). (F+G) Please write the solution handwriting.
What is RG rating of coaxial cable. Please give me detailed information. Don't copy previously given Answer
4. Do some search about the functionality of Airport Metal Detectors. Explain your answer in a paragraph.
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
Please answer quickly. 17. The filament of incandescent lamp is usually made of: a. copper b. silver c. aluminum d. tungsten 18. A current measuring instrument can be modified to measure voltages by: a. using thicker wire in the coil b. using a high resistance shunt c. adding resistance in series d. adding resistance in parallel 21. "When two power sources are connected in a series-aiding configuration, the output voltage equals the _____________" a. supply with the highest voltage b. supply with the lowest voltage c. difference of the two supplies d. sum of the two supplies