In the figure, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg, and the pulley is a hollow cylinder with a mass M = 0.350 kg, a interior radius R1 = 0.0200 m and an exterior radius R2 = 0.0300 m. Assume that the mass of the rays is negligible. The coefficient of kinetic friction between the block and the surface horizontal is µk = 0.250. The pulley rotates without friction on its axis. The lightweight cable does not stretch and does not slip on pulley. The block has a velocity of vi = 0.820 m / s towards the pulley when you pass a landmark on the table. (a) Use energetic methods to predict its velocity after it has passed a second point, which is at 0.700 m. (b) Find the angular speed of the pulley at the same moment.

Q: Q4. As shown in the image below, a force of P= 310 N is applied to the 64-kg cart. The dimensions…

A: To find : To find the total normal reaction at the wheel A. Given :   force P=310 N…

Q: 21° W A 190 kN horizontal force Pis applied to a 220 kN box resting on an 21° incline. The line of…

A:

Q: An ideal cord (no mass and no elongation under load) is wrapped around a disc of radius r (r=50 cm,…

A:

Q: V mg Sw mg 2. A drone of mass m (shown above) moves with a horizontal velocity v and is propelled by…

A:

Q: The hoop (thin ring) has a mass of 5 kg and is released down the inclined plane such that it has a…

A:

Q: The 10 kg slender bar AB, shown in the figure, has a length of 2 m. A block of negligible mass,…

A:

Q: A rope of length L = 2.2 m and mass m = 5 kg is initially at rest and can slide on an inclined surf…

A: To calculate the maximum value of b for which the rope will not start sliding down the slope, we…

Q: Motorized moving platform is lifting a car with some acceleration. If the combined weight of the…

A: Mass of platform = 2800 kgMass of the lift = 200000 kgFind the maximum acceleration before tipping

Q: This climber (mass=52kg) is maintaining this posture while grabbing onto a rock at P3 and reaching…

A:

Q: The 1.0 kg block in the figure is tied to the wall with a rope. It sits on top of the 2.0 kg block.…

A: According to the given data  m1=1kg m2=2kg the friction coefficient for both surfaces of block 2…

Q: Body U with mass 5m is stacked on the top body W with mass m, and released. The bodies are in…

A: Consider the Free body diagram: Given:Weight of body U=5mgWeight of body W=mgFrom the…

Q: How far have you pulled the block and cylinder when everything stops?

A:

Q: A homogeneous thin circular disk Dof mass 6.8-kg,and radius R=o.74 is able to roll without slipping…

A:

Q: A block of mass m₁ = 1.95 kg and a block of mass m₂ = 6.45 kg are connected by a massless string…

A: m1=1.95kg m2=6.45kg M=10kg R=0.250m N=10kg θ=30° μ=0.36 We need to find Acceleration of the two…

Q: Block A in the figure weighs 1.16 N and block B weighs 3.62 N. The coefficient of kinetic friction…

A: According to the given data WA=1.16 N WB=3.62N μ=0.293 We need to find (a) Find the magnitude of the…

Q: A file cabinet weighing 215 lb is being pushed to the right with a horizontal force P applied a…

A: The maximum height at which the cabinet can be pushed and the acceleration of the cabinet. Given:…

Q: A cylinder is rotating in clockwise direction. It is to be stopped by a band brake (also known as…

A:

Q: A block of mass m, 2.40 kg and a block of mass m₂ = 5.90 kg are connected by a massless string over…

A:

Q: o blocks with masses M1 and M2 are connected by a massless string that passes over a pulley as…

A: Now acceleration of whole the system is same. So acceleration is a=a2=0.52 m/s2

Q: Find the minimum weight of block A in order for motion to be impending down the plane (to the left).…

A:

Q: Figure shows a system of cylinder (m = 55 kg) and a load (m = 62 kg) connected through a rope. The…

A:

Q: What is its position and velocity at t= 9.2 s? What is the new velocity and new position?

A:

Q: Mass of both blocks F 14kg. The friction coefficient for this bar is µ= 0.4. The spring constant k=…

A: Given data: Mass of both blocks A and B are mA = mB = 14 kg. The friction coefficient is μ=0.4. The…

Q: In the figure, a slab of mass m, = 40 kg rests on a frictionless floor, and a block of mass m, = 9…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.