A block of mass m, 2.40 kg and a block of mass m₂ = 5.90 kg are connected by a massless string over a pulley in the shape of a solid disk having radius R = 0.250 m and mass M- 10.0 kg. The fixed, wedge-shaped ramp makes an angle of 0 = 30.0° as shown in the figure. The coefficient of kinetic friction is 0.360 for both blocks. Use g-9.8 m/s². M, R My mo (b) Determine the acceleration of the two blocks. (Enter the magnitude of the acceleration.) m/s² (c) Determine the tensions in the string on both sides of the pulley. left of the pulley N right of the pulley N

Q: 1. Which type would make the solution most readable?

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: you did not derive an equation you only did an explanation thumbs down

A:

Q: What is a microcontroller? 1. General purpose device that can be programmed to carry out a finite…

A: Given question is related to electromechanical devices and controllers.

Q: I need problems 10, 11, and 12 answered pertaining to the print attached below.

A: The print sheet shows the 3D perspective of the part BACK CAP generally used in TIG Welding. It is…

Q: From among the following select the truest statement. The Distortion Energy theory is a special case…

A: The given problem is based on theory of failure.

Q: This answer is incorrect. Can someone else help me solve this again ?

A: given data

Q: Compute the moments of inertia with respect to the X-X and Y-Y centroidal axes for the following…

A:

Q: Q1: Select the correct answer. ( A. Resilience is the energy absorbed by the material up to a.…

A: According to the guidelines, I can solve only first three subparts. For rest problem, repost in a…

Q: Which of the following statement is correct? O Discontinuities can propagate and become defects. O…

A: ◆ The discontinuity is the imperfection on the physical surface of the objects. The examples of…

Q: Procedure: 1. Look up the materials that make up a smartphone. Take notes in a table like the one…

A: Minerals are the substance found in the earth's crust useful to mankind. Smartphone is a Pinnacle of…

Q: A. Resilience is the energy absorbed by the material up to a. yield. b. ultimate sensile stress. c.…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: I need these three parts answered, if you can not answer all three parts please leave it for another…

A: 8.Refer to the drawing. The material specified for the given part is brass. It is shown in the…

Q: What is the temperature of an object where it is half as hot as 80 degrees Fahrenheit?

A: The temperature is 80°F The temperature of an object is half of the given temperature.

Q: I need answers to questions 4, 5, and 6 pertaining to the print provided.

A: Since we question only one question, we will answer the question no. 10. Please submit the question…

Q: 2. Determine the moment about point C due to the forces shown. Note: 4 kips is perpendicular to the…

A: Given   Load, P1 = 2 kips             P2 = 4 kips Find  Moment of a force about point C

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: 3. A simply supported beam is shown below. Do the following. a) Draw the equivalent load diagram. b)…

A:

Q: Please answer questions 7,8, show reasons and examples

A: The characteristic equation of the system is:x^6 + (73*x^5)/40 + (1969*x^4)/48 + (22309*x^3)/600 +…

Q: 2. A simply supported beam is shown below. Do the following. a) Draw the equivalent load diagram. b)…

A:

Q: Particles less than in diameter are generally referred to as the fine mode: a. 0.75 μm; b. 7.5 um;…

A: This question is based on the concept of size of particles.

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A:

Q: Q1: Select the correct answer. A. Resilience is the energy absorbed by the material up to a. yield.…

A: As per the company's guidelines when multiple choice questions are asked only first 3 questions have…

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.