In the figure, one end of a uniform beam of weight 440 N is hinged to a wall; the other end is supported by a wire that makes angles 0 = 32° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge D

In the figure, one end of a uniform beam of weight 440 N is hinged to a wall; the other end is supported by a wire that makes angles 0 = 32° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge D

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 33PQ: Problems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a...

See similar textbooks

Similar questions

Problems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in Figure P14.33. Find the tension in the cable. FIGURE P14.33 Problems 33 and 34.
A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.
In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?
Check Your Understanding A 400.0-N sign hangs from the end of a uniform strut. The strut is 4.0 m long and weighs 600.0 N. The strut is supported by a hinge at the wall and by a cable whose other end is tied to the wall at a point 3.0 m above the left end of the strut. Find the tension in the supporting cable and the force of the hinge on the strut.
In the figure, one end of a uniform beam of weight 390 N is hinged to a wall; the other end is supported by a wire that makes angles 0D 32° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge (a) Number Units (b) Number Units (c) Number Units
Inthe figure, one end of a uniform beam of weight 440 N is hinged to a wall; the other end is supported by a wire that makes angles 8= 26° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge (a) Number Units (b) Number Units (c) Number Units
A uniform beam is 5.00 m long and has a mass of 53.0 kg. The beam is supported in a horizontal position by a hinge and a cable, with angle ? = 115°.(a) Draw all the forces acting on the beam.(b) What Newton’s Law will you use to solve this problem?(c) What is the tension ?? on the cable?(d) What are the magnitude of the vertical and horizontalforces acting on the hinge ???(e) What is the magnitude and direction of the torque ??exerted by the tension on the cable?
A beam with length of 2 m and a mass of 10 kg supports a 50 kg box. The beam is connected to a wall by a hinge at its base and a horizontal wire. The wire is connected to the beam 1.5 m from the hinge and makes an angle θ of 35o to the beam. The goal is to find the tension in the wire and the horizontal and vertical components of the force exerted by the hinge on the board. Suppose the maximum tension that the wire can withstand is 1500 N. What is the maximum load that the hinge can support before the wire breaks?
A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath. The drawbridge weights 55000 N and is 15.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place. What is the tension in the cable? Find the magnitude and direction of the force the hinge exerts on the bridge. If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks? What is the angular speed of the drawbridge as it becomes horizontal? What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?
In the figure, one end of a uniform beam of weight 280 N is hinged to a wall; the other end is supported by a wire that makes angles θ = 28° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam.
A safe mass M = 430kg hangs by a rope from a boom has a mass m = 85kg. Find the tension T, in the cable and the magnitude of the net force exerted on the beam by the hinge. Cable Rope (a) Hinge Beam com
A 1260 N uniform beam is attached to a vertical wall at one end and supported by a cable on th other end. A 1960 N crate hangs from the far end of the beam. Using the info on the diagram find the following: a) Magnitude of the tensiossnj on the cable b) the horizontal components of the varce that the wallexerts on the beam c) the vertical components of the force that the wall exerts on th eleft end of the bean