In the figure, block 1 has mass m₁ = 460 g, block 2 has mass m₂ = 590 g, and the pulley is on a frictionless horizontal axle and has radius R = 4.8 cm. When released from rest, block 2 falls 75 cm in 4.5 s without the cord slipping on the pulley. (a) What is the magnitude of the acceleration of the blocks? What are (b) tension T2 (the tension force on the block 2) and (c) tension T₁ (the tension force on the block 1)? (d) What is the magnitude of the pulley's angular acceleration? (e) What is its rotational inertia? Caution: Try to avoid rounding off answers along the way to the solution. Use g = 9.81 m/s². (a) Number Units (b) Number Units (c) Number Units (d) Number Units m1 <> <> <> M2

In the figure, block 1 has mass m₁ = 460 g, block 2 has mass m₂ = 590 g, and the pulley is on a frictionless horizontal axle and has radius R = 4.8 cm. When released from rest, block 2 falls 75 cm in 4.5 s without the cord slipping on the pulley. (a) What is the magnitude of the acceleration of the blocks? What are (b) tension T2 (the tension force on the block 2) and (c) tension T₁ (the tension force on the block 1)? (d) What is the magnitude of the pulley's angular acceleration? (e) What is its rotational inertia? Caution: Try to avoid rounding off answers along the way to the solution. Use g = 9.81 m/s². (a) Number Units (b) Number Units (c) Number Units (d) Number Units m1 <> <> <> M2

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

One of the rides at an amusement park consists of small cars that are supported by steel cables 5.00 m long and rotated in a circle at gradually increasing speed. As the speed increases, the cars rise. Find the speed of a car when the cable makes an angle of 35.0 degrees with the vertical.
In the figure, a rectangular slab of slate rests on a bedrock surface inclined at angle 8 = 22.8°. The slab has length L = 48.9 m, thickness T = 6.61 m, and width W = 12.7 m, and 1.0 cm³ of it has a mass of 3.2 g. The coefficient of static friction between slab and bedrock is 0.312. (a) Calculate the component of the gravitational force on the slab parallel to the bedrock surface. (b) Calculate the magnitude of the static frictional force on the slab. By comparing (a) and (b), you can see that the slab is in danger of sliding. This is prevented only by chance protrusions of bedrock. (c) To stabilize the slab, bolts are to be driven perpendicular to the bedrock surface (two bolts are shown). If each bolt has a cross-sectional area of 6.47 cm² and will snap under a shearing stress of 3.59 x 108 N/m², what is the minimum number of bolts needed? Assume that the bolts do not affect the normal force.
A mass (M1=5.0 kg) is connected by a light cord to another mass (M2=3.0 kg) which slides on a frictional surface (μ1 = 0.25). moreover, another mass (M3=2.0 kg) is connected by a light cord to the mass M2. The coefficient of friction between M2 and M3 is μ2 = 0.2. The two pulleys (radius= 0.1 m) are identical and can rotate about a frictionless axle. If the moment of inertia of a pulley is 0.2 kgm2, what is the acceleration of M1? Calculate the tension of each string?
The figure shows a box of dirty money (mass m₁ = 3.5 kg) on a frictionless plane inclined at angle 0₁ = 34°. The box is connected via a cord of negligible mass to a box of laundered money (mass m₂ = 1.6 kg) on a frictionless plane inclined at angle 02 = 68°. The pulley is frictionless and has negligible mass. What is the tension in the cord? Number Units M²1 m2 02/
A cord passing over a pulley connects two masses, as shown, where m, = 3.60 kg and m, = 7.10 kg. The system accelerates with a magnitude of 1.34 m/s?. The coefficient of kinetic friction between the masses and the incline is the same for both masses. Assume the pulley is frictionless, and the cord is massless. (Due to the nature of this problem, do not use rounded intermediate values in your calculations-including answers submitted in WebAssign.) m2 m, 35.0° 35.0° (a) What is the coefficient of kinetic friction? (b) What is the tension (in N) in the cord?
In the figure, a cord runs around two massless, frictionless pulleys. A canister with mass m = 41 kg hangs from one pulley, and you exert a force F on the free end of the cord. (a) What must be the magnitude of F if you are to lift the canister at a constant speed? (b) To lift the canister by 3.5 cm, how far must you pull the free end of the cord? During that lift, what is the work done on the canister by (c) your force (via the cord) and (d) the gravitational force? (Hint: When a cord loops around a pulley as shown, it pulls on the pulley with a net force that is twice the tension in the cord.) (a) Number i Units (b) Number i Units (c) Number Units (d) Number i Units
A "swing" ride at a carnival consists of chairs that are swung in a circle by L = 15.8 m cables attached at an angle of θ = 57.4° to a vertical rotating pole, as the drawing below shows. Suppose the total mass of a chair and its occupant is 161 kg. Calculate the tension in the cable attached to the chair.
In the figure, a rectangular slab of slate rests on a bedrock surface inclined at angle θ = 28.4°. The slab has length L = 32.4 m, thickness T = 5.92 m, and width W = 14.3 m, and 1.0 cm3 of it has a mass of 3.2 g. The coefficient of static friction between slab and bedrock is 0.385. (a) Calculate the component of the gravitational force on the slab parallel to the bedrock surface. (b) Calculate the magnitude of the static frictional force on the slab. By comparing (a) and (b), you can see that the slab is in danger of sliding. This is prevented only by chance protrusions of bedrock. (c) To stabilize the slab, bolts are to be driven perpendicular to the bedrock surface (two bolts are shown). If each bolt has a cross-sectional area of 6.05 cm2 and will snap under a shearing stress of 3.34 × 108 N/m2, what is the minimum number of bolts needed? Assume that the bolts do not affect the normal force.
In the figure, a rectangular slab of slate rests on a bedrock surface inclined at angle 8 = 29.4°. The slab has length L = 46.9 m, thickness T = 5.52 m, and width W = 12.5 m, and 1.0 cm³ of it has a mass of 3.2 g. The coefficient of static friction between slab and bedrock is 0.309. (a) Calculate the component of the gravitational force on the slab parallel to the bedrock surface. (b) Calculate the magnitude of the static frictional force on the slab. By comparing (a) and (b), you can see that the slab is in danger of sliding. This is prevented only by chance protrusions of bedrock. (c) To stabilize the slab, bolts are to be driven perpendicular to the bedrock surface (two bolts are shown). If each bolt has a cross-sectional area of 5.60 cm2 and will snap under a shearing stress of 3.56 x 108 N/m², what is the minimum number of bolts needed? Assume that the bolts do not affect the normal force. (a) Number (b) Number (c) Number Units Units Units
A toy jeep rolls down an incline at a constant velocity. The jeep's mass is m = 1.9 kg and the ramp makes an angle of θ = 17 degrees with respect to the horizontal. Assume the rolling resistance is negligible. Assuming the jeep experiences only air resistance in opposition to its motion, with magnitude Fr. Write an expression for the sum of the forces in the x-direction using the acceleration due to gravity, g, and the variables provided.
A 30.6 kg mass (m) is suspended by the cable assembly as shown in the figure. The cables have no mass of their own. The cable to the left (T|) of the mass makes an angle of 0.00° with the horizontal, and the cable to the right (T2) makes an angle (02) of 36.4°. If the mass is at rest, what is the tension in T each of the cables, T¡ and T,? The acceleration due to gravity is g = 9.81 m/s². T = N m T2 = N
Look carefully at the image below. An object with mass m is released from rest at a height R above the ground. The acceleration due to gravity is g. The block slides along the inside of a frictionless circular loop of radius R. ♡ Which one of the following expressions gives the speed of the block at the bottom of the hoop? a) v = mg 2R b) ² = R zero m/s² d) 2² = 2gR e) v = mgR (