Please show your solutions E) 16.64F) 46.15G 61.54H) 25.60 In the figure below, the trusses are all stable. Compute the magnitude of reaction at C in kips.Elinktruss 1truss 215'40'20'15'ВlinkD20'24 kips60 kipsAk 20'e 20' →t 20'–→k– 20' →le 20'–|A52.06B40.8331.15D38.40

Answered: Image /qna-images/answer/b7e7b632-5e2f-4762-ba07-54886a8f3727.jpg

Answered: In the figure below, the trusses are…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(a) A turning operation is performed on a 660 mm cylindrical part of a certain alloy. The work material has a length of 140 mm as shown in Figure Q3-1. The finished (produced) part is shown in Figure Q3-2 which has an overall length of 100 mm. The remaining part of the raw material length is kept as a gripped part on the turning machine chuck. The cutting data is shown in Table Q3(a). Apply engineering calculations on the given metal cutting operations, Table Q3(a) Depth of cut Feed 2.5mm 0.15mm/rev Cutting Speed Rake angle The chip thickness after cut Shear strength 40m/min 50 0.17mm 280 MPa (i) Shear force. (ii) Coefficient of friction. e (iii) Cutting force. (iv) Time required to cut the part (v) Rate of material removal. 50mm $60mm -20mm 60 mm 140 mm 40 mm Figure Q3-1 Figure Q3-2 4 1 + DRG Ans Realm ? Ran x10*
For bar drawing, semi-die angle.may vary between a. 0 and 5 degree 20 and 25 degrce 6 and 20 degree b. C. d. 25 and 30 degrce
04 05 a Explain the reasons for the following: 1- The pure aluminum and the copper are generally rated as easy to machine 2- In ultrasonic machining, the stress produced by the impact of abrasive particles on the workpiece surface is high. 3- In rolling process, the coefficient of friction must be sufficient. 4- Difference in solidification between casting and welding processes. 5- Why is it desirable to use energy sources for welding that have high heat densities? 6- Why there might be a change in the density of a forged product as compared to that of the cast blank. D. A cylindrical workpart with D=2.5 in and h=2.5 in is upset forged in an open die to a height = 1.5 in. Coefficient of friction at the die -work interface = 0.10 The work material has a flow curve defined by: K= 40,000 lb/in' and n-0.15. Determine the instantaneous force in the operation (a) just as the yield point is reached (yield at strain = 0.002), (b) at height = 2.3 in. (c) h= 1.9 in, and (d) h = 1.5 in. a List…
6. How large of a square may be milled on the end of a 2 1/2-inch bar of round stock? Page #
What would a .010 - .020 cutback of a 14.500 Diameter be?
5- Complete the sentence with the correct statement for rolling operation. In the the strip is rolled continuously, through a number of stands. a) Tandem rolling mill b) Four-high mills Two-high mill Cluster mill Three-high mill
nQ2. Write short notes on Surface treatment process. List any two examples for Joining and assembly process.
QUESTION 16 Riser is a cavity connected to the gating system feeding the casting when it is shrinking. O True O False QUESTION 17 In a sheet-metal shearing operation (Punching) used to produce a flat part with a hole in the centre, the part itself is discarded and the piece that is cut out to make the hole is called a scrap. O True O False QUESTION 18 Pieces thicker than 5.45mm are considered sheet. O True O False
Power is supplied at the rate of 0.40 hp for 2 min in drilling a hole in a 1.0 lb brass block. (a) How much heat is generated? (b) What is the rise in temperature of the brass if 75% of the heat generated warms the brass? What happens to the other 25%? (don't change the hp, lb)
None
Q.2- Answer two of the following: a) State the types of sheet metal bending process and compare (in table) between them. b) What the Difference between brazing and soldering? (Compare in table). c) Compare (in table) between shaping and planing operations.
2. Calculate the blank size for the following sheet metal bending operation when the thickness of the sheet is 4mm, R-1.5t, A-60mm, B-250mm and C-80mm.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

In the figure below, the trusses are all stable. Compute the magnitude of reaction at C in kips. E link truss 1 truss 2 15' 40' 20' 15' В link D 20' 24 kips 60 kips