Solution? ClosePROBLEM 1.33 in.2 in.30 kips BTwo solid cylindrical rods AB and BC are welded togetherat B and loaded as shown. Determine the magnitude of theP30 kipsforce P for which the tensile stress in rod AB is twice themagnitude of the compressive stress in rod BC.30 in.40 in.SOLUTIONA AB-(2)² = 3.1416 in?K 5/ 1806 >O AB...

Answered: Image /qna-images/answer/cfd4b66a-f52f-4072-bcf6-9dff07bf0495.jpg

PROBLEM 1.3 3 in. 2 in. 30 kips B Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the 30 kips force P for which the tensile stress in rod AB is twice the magnitude of the compressive stress in rod BC. 30 in. 40 in.

PROBLEM 1.3 3 in. 2 in. 30 kips B Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the 30 kips force P for which the tensile stress in rod AB is twice the magnitude of the compressive stress in rod BC. 30 in. 40 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Which of the following metal forming processes is best suitable for making the cup shaped products? a. Rolling O b. Forging O c. Drawing O d. Extrusion
3XPL@!N THE PROCESS @ND PROVIDE EXAMPLES FORMING OPERATIONS 1. Forging is mechanically working or deforming a single piece of a usually hot metal; this may be accomplished by the application of successive blows or by continuous squeezing. 2. Rolling, the most widely used deformation process, consists of passing a piece of metal between two rolls; a reduction in thickness results from compressive stresses exerted by the rolls. 3. Extrusion, a bar of metal is forced through a die orifice by a compressive force that is applied to a ram; the extruded piece that emerges has the desired shape and a reduced cross-sectional area. 4. Drawing is the pulling of a metal piece through a die having a tapered bore by means of a tensile force that is applied on the exit side.
Q3 Give the reason for 10 of the following. - 1- The use of lubricant in wire drawing die. 2- The uses of tungsten carbide for the manufacturing of die tool. 3- The increase of Mo/Si ratio during the production of white cast iron. 4- The addition of Al to copper alloys. 5- Aluminum is a better overall conductor than Copper for long distance electric transformation. 6- The addition of cryolite in smelting electrical furnace due to the production of aluminum. 7- The addition of Magnesium and Cerium during the production of Ductile cast iron. 8- The addition of 13% Cr to steel in corrosive environment. 9- The increase of hardness for chips due to the cutting process. 10- The brittle fracture of steel at low temperature lower than -4 C. 11- The heating of metal after the rolling process.
Today, the two most important processes in steelmaking are which of the following (two correct answers): Group of answer choices basic oxygen furnace Bessemer converter electric arc furnace induction furnace open hearth furnace answers a and c
nQ2. Write short notes on Surface treatment process. List any two examples for Joining and assembly process.
None
Manufacturing Processes Q1. Chose the correct answer: 1. Which of the following are variations of sheet-metal-bending operations: (a) coining, (b) flanging, (c) hemming, (d) ironing, (e) notching, (f) shear spinning, (g) trimming, and (h) tube bending? 2. Springback in a sheet-metal-bending operation is the result of which one of the following: (a) elastic modulus of the metal, (b) elastic recovery of the metal, (c) overbending, (d) overstraining, or (e) yield strength of the metal? 3. The cutting force in a sheet-metal blanking operation depends on which mechanical property of the metal (one correct answer): (a) compressive strength, (b) modulus of elasticity, (c) shear strength, (d) strain rate, (e) tensile strength, or (f) yield strength? 4. A circular sheet-metal slug produced in a hole punching operation will have the same diameter as (a) the die opening or (b) the punch? 5. As sheet-metal stock hardness increases in a blanking operation, the clearance between punch and die should…
Q2 (a) A sliding door rail as shown in Figure 2.1, is to be produced using steel as the raw material. If direct extrusion is to be used, at what temperature range (degree Celsius) and extrusion pressure range (MPa) the process should be carried out? Figure 2.1 A sliding door rail
1. Define manufacturing processes, design engineer, industrial engineer and materials engineer? 2. Name and explain a protess to make cylinder shaft? 3. Discus at least three factors which will effect tool life? 4. Define finishing and roughing process? 5. Explain the negative effect of heat generated from machining process? 6. One limitation of sand casting is bad surface finish. Yes or No? Why? 7. What is permeability in casting process? 8. What are the major defects in casting process? 9. Which type of casting process should be use for high melting point casting, such as cast iron and why? 10. Casting problem A certain mold has a sprue whose length is 20 cm and the cross-sectional area at the base of the sprue is 2.5 cm?. The sprue feeds a horizontal runner leading into a mold cavity whose volume is 1560 cm³. Determine: (a) velocity of the molten metal at the base of the sprue, (b) volume rate of flow, and (c) time to fill the mold (in second). mfg m1 Spring 2020 999.pptx
I need answer within 20 minutes please please with my best wishes
where are the steps for the solution?????