In the diagram, Force F must pull with 30N to keep the system in static equilibrium, what is the weight? If the diameter of Gears D and G were changed to 14 cm, what would the required force to hold the system in equilibrium be? (Use the weight calculated previously)

Q: The pulley system shown in Figure Q1c lifts a mass, m, of 550 kg. Calculate the force FA necessary…

A:

Q: Consider a system of two toy railway cars (i.e., frictionless masses) connected to each other by…

A: Given: m1=4 kgm2=4 kgk1=256 N/mk2=384 N/mk3=256 N/m To find: Equation of motion in matrix form…

Q: The rod AB is held in equilibrium by a vertical wall, the horizontal floor and by a cable CB.…

A:

Q: Assume the smooth inclined plane 550 Figure P-309 1. Determine the Maximum Weight of the Cylinder…

A: Given Cylinder To find Weight of the cylinder for maximum rod force is 300 kN Hinge reaction for…

Q: 13. Consider the system of planar rigid bodies as shown in figure. (a) Construct the free body…

A:

Q: A stepped bar is held in equilibrium by several forces acting at different points along the length,…

A:

Q: 2. A 4-lb weight stretches position equilibrium external force f(x): = a spring 6 in. The weight is…

A:

Q: Can you give me the free-body diagram?

A: Given data:- A pendulum of mass M1=1 kg  length L = 0.75 m . Mass of Block M2= 2 kg To find :- Free…

Q: The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is…

A:

Q: The hoist supports the 125-kg engine (Figure 1). Figure G -1 m - F -2 m 2 m H 1m- 1 of 1 E 2 m 1 m…

A: The hoist supports the 125-kg engine (Figure 1).Determine magnitude of the force the load creates in…

Q: Draw the free- statement. You are NOT required to write or solve any equilibrium equation should…

A: Given-Information:- Length AD, l = 4.5 m To-Determine:- 1. Reaction at pin A. 2. Force in the cable…

Q: also find ax and ay The rod is supported by smooth journal bearings at A, B. and Cand is subjected…

A:

Q: In both words and equations, state the two conditions which must be satisfied for a rigid body to be…

A: 1.The resultant of all external forces must be zero.∑F=0 2.The resultant of all external torques…

Q: Example Neglecting weight, determine M if the link is in equilibrium. 150 mm M 150 mm 60° 30°

A: Draw the free body diagram for the above problem.

Q: rque Problem diagram below shows the lower leg being held in a stationary. The torque ng to turn the…

A: Angle made with horizontal = 50° Weight of leg WL = 90 N Weight of barbel Wb = 120 N Quadriceps…

Q: Given: The plate( The shaded rectangular volume) has weighs 240 lbf. It is. suspended by able CD,…

A: Given: To find: Tension in cable CD

Q: A landing gear mechanism is shown in the accompanying figure. You may assume that it is in static…

A: Solution: Given Data: W=225 lb   To Find: (a) The force in link AB. (b) The magnitude of the pin…

Q: Suppose you have three springs with force constants of k₁ = k₂ = k3 = 3.30 x 10³ N/m. What is their…

A: According to the question three springs with equal spring constant K1=K2=K3=3.30x103N/m connected in…

Q: Find the horizontal and vertical components of the pin reactions at C and the magnitude of the…

A:

Q: A horizontally positioned door weighing 1200 N is held in place by hinges centered at points A and B…

A: Given: The weight of door, W = -1200k

Q: pls explain to me step by step and pls dont skip any steps i will rate your answer immediately…

A: given data as per question force to be generated = 500 N dimension of a1 =100 mm dimension of a2…

Q: A flat bar ABCDEF of negligible mass is hinged at A and supported by a roller support at D as shown…

A:

Q: Two farmers are pushing on a gate with forces F_{A} and F_{B} applied at locations A and B…

A: α= 30∘, β= 35∘, FA= 400 N, DAC= 3 m