In the design of a conveyor-belt system, small metal blocks are discharged with a velocity of 0.4 m/s onto a ramp by the upper conveyor belt shown. If the coefficient of kinetic friction be- tween the blocks and the ramp is 0.30, calculate the angle which the ramp must make with the horizontal so that the blocks will transfer without slipping to the lower conveyor belt moving at the speed of 0.14 m/s. 0.40 m/s 1.5 m 0.14 m/s

In the design of a conveyor-belt system, small metal blocks are discharged with a velocity of 0.4 m/s onto a ramp by the upper conveyor belt shown. If the coefficient of kinetic friction be- tween the blocks and the ramp is 0.30, calculate the angle which the ramp must make with the horizontal so that the blocks will transfer without slipping to the lower conveyor belt moving at the speed of 0.14 m/s. 0.40 m/s 1.5 m 0.14 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a test of the operation of a "cherry-picker" fire truck, the equipment is free to roll with its brakes released. For the position shown, the truck is observed to deflect the spring of stiffness k = 14.2 kN/m a distance of 171 mm because of the action of the horizontal stream of water issuing from the nozzle when the pump is activated. If the exit diameter of the nozzle is 35 mm, calculate the velocity v of the stream as it leaves the nozzle. Also determine the added moment M which the joint at A must resist when the pump is in operation with the nozzle in the position shown. Answers: V= M= i i 4.6 m 81 70° 17.6 m m/s kN-m
2. A mass m and a spring of stiffness k are connected in series. The mass lies on a horizontal floor with coefficient of friction u. At t = 0, the free end of the initially unstressed spring is moved at a constant speed vo in a straight line directly away from the mass. Draw the FBD of the block, and Find: (i) the equation of motion of the block, (ii) the time ti at which the motion of the block is initiated, and (iii) the subsequent motion x(t) of the block
3 kg mass (green block) slides along the rod at a speed of 1.5m/s. Calculate the force of the impact at the other end when the green mass impacts the endcap. Length of rod is 300 mmMass of green block is 3 kgDiameter of rod is 15 mmVelocity of green block is 1.5 m/s
3/138 The 25-kg slider in the position shown has an initial velocity vo= 0.6 m/s on the inclined rail and slides under the influence of gravity and friction. The co- efficient of kinetic friction between the slider and the rail is 0.5. Calculate the velocity of the slider as it passes the position for which the spring is com- pressed a distance x = 100 mm. The spring offers a compressive resistance C and is known as a "hard- ening" spring, since its stiffness increases with de- flection as shown in the accompanying graph. 1 m = 0.6 m/s 60° 25 kg = 0.5 Hk= C, KN Problem 3/138 x, m 62x2 ✓ 18x
A 200-lb block is sliding along a horizontal plane at 4 ft/s when a force P is applied on it as shown. The magnitude of P varies according to the relation P = 200t Ib where t is in sec. Find the velocity of the block 2 sec after P is applied. Neglect friction. Use Impulse-Momentum Method and draw the momenta and impulse vectors. 4 fes 200 lb
A sled weighing 100 lb reaches the foot of a hill with a speed of 40 ft/s. The coefficient of kinetic friction between the sled and the horizontal surface of the ice at the foot of the hill is 0.03. Determine the force exerted by the sled.
(a) A force of 50 N inclined at an angle of 300 with the vertical axis moves a square block of mass 6 kg that is initially at rest on a horizontal table. The force is applied with an inextensible rope attached at the top right corner of the block. Find the velocity of the block after 8 secs. Take coefficient of kinetic friction as 0.2.
Hello Sir.Good Night I have a question in my homework related chemical material lesson. The following below is my question.Please advice, thank you. "Explain the stages of the metal strengthening process ?"
Find the velocity of body A after it has moved, startingfrom rest at the given position, for 9 ft along the surfaceshown. The coefficient of friction between block A and thesurface is 0.35.
A body of weight 370 N body moving to the left with a velocity of 14 m/s collides with another body of weight 690 N body which is at rest. After impact the body which is moving before impact comes to rest. Find the final velocity of body after impact and the coefficient of restitution The final velocity of body after impact in m/s is The coefficient of restitution is
6) In the figure shown, body A is connected to body B by a cord which goes through smooth rollers at C. Body A weighs 15 lb and body B weighs 12 lb. The coefficient of friction between body A and the horizontal surface is 0.6. At the instant shown the cord connecting body A to the wall is cut. What is the minimum velocity body B must have in order to cause body A to slide. What is the tension in the cord at this instant. 30° 3.0'
In the situation illustrated in the figure below, a small package is deposited by a conveyor belt at point A onto a ramp at theta = 35 degrees degrees to the horizontal with a velocity of 0.5m / s . The distance between points A and Bis 2 m. a)Calculate the maximum value mu k ^ * of the kinetic friction coefficient between the package and the ramp AB for which the parcel reaches point B. b) If the actual kinetic friction coefficient between the package and AB and BCis mu k =0.5 mu k ^ * calculate the distances on the level surface BC at which the package comes to rest. Note: if you haven't been able to solve part a), take the actual kinetic friction coefficient equal to mu_{k} = 0.28