2. A mass m and a spring of stiffness k are connected in series. The mass lies on a horizontal floor with coefficient of friction u. At t = 0, the free end of the initially unstressed spring is moved at a constant speed vo in a straight line directly away from the mass. Draw the FBD of the block, and Find: (i) the equation of motion of the block, (ii) the time ti at which the motion of the block is initiated, and (iii) the subsequent motion x(t) of the block

2. A mass m and a spring of stiffness k are connected in series. The mass lies on a horizontal floor with coefficient of friction u. At t = 0, the free end of the initially unstressed spring is moved at a constant speed vo in a straight line directly away from the mass. Draw the FBD of the block, and Find: (i) the equation of motion of the block, (ii) the time ti at which the motion of the block is initiated, and (iii) the subsequent motion x(t) of the block

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ex.6.2 (Dynamics by Meriam and Kraige) The system is released from rest with the cable taut. For the friction coefficients, µs = 0.25 and Hk = 0.20, calculate the acceleration of each block and the tension T in the cable. Neglect the small mass and friction of the pulleys. Try it!!! 60 kg 20 kg 30° B
B6
Suppose that you are designing a system to prevent the contents of packages from being damaged when they slide off of a conveyor line. Your solution is to have a linear spring that compresses 6 inches when a package weighing 80 pounds impacts the system at a speed of 10 feet per second. What value of k, the spring constant, should you specify? Assume that the spring is at its free length before the package makes contact, and that friction can be neglected. (Hint: remember to use consistent units!) 10 ft/s www. Problem 4: What is the maximum acceleration in g's that the package in the previous problem will experience? (Use equations of motion for this problem.)
H4.
T my F Two blocks connected by a rope of negligible mass are being dragged by a horizontal force F. Suppose that F=68.0 N, mị = 12.0kg, m2 = 18.0kg, and %3D the coefficient of kinetic friction between each block and the surface is 0.1. (a) Draw a free-body diagram for each block. (b) Find the acceleration of the system. (C) Determine the tension T of the rope between the blocks.
A steel ball of mass M is held at a distance H above a massless rigid tabletop supported by undamped springs whose equivalent stiffness is K. If the ball is left to fall from rest on the tabletop. Deduce an expression for the velocity at which the ball will bounce back off the tabletop. On its way back, will the mass bounce back to its initial height? If it will not, where will the difference in energy go? Discuss mathematically! (Pls solve the question in detail with figure)
I need a clear and fast answer within 20 minutes. Thank you
Problem 1. Find the horizontal force magnitude P needed to start the motion of the block with mass mo in two scenarios: (a) when P is applied to the right and (b) when P is applied to the left. Develop a general solution for each scenario, and subsequently, substitute the values 0= 25°, m = mo = 2.5 kg, µs = 0.40, and μk = 0.35 into your expressions for evaluation. Hgs H k P (a) A mo 0 m P (b) B
A block of mass m₁ is suspended from the ceiling with a spring k and damper b. Attached to the block is a massless rod of length L. Affixed to the end of the rod is a point-mass of mass m₂. Gravity is acting in the direction indicated in the figure. Use the energy method to set up the energy expression you would use to calculate the equations of motion for the system. Hint: be sure to decompose the velocity of the pendulum into horizontal and vertical components. DO NOT CALCULATE THE EQUATIONS OF MOTION, only setup the energy expression. x(t) b 7 m₁ e(t) (m₂
A slender bar with a length of 2 ft is pin-connected with a roller positioned on a smooth horizontal surface. The bar is at rest initially, and a horizontal force F is applied to the roller. If F = 13 lb and the weight of the bar is 10 lb, calculate the magnitude of the acceleration of the roller at that instant by neglecting the mass and the size d of the roller. Present your answer in ft/sec² using 3 significant figures. FOR COMARCA 2 ft F
State the equation that mathematically represents the system. All in domain X(s) hint: there are 3 equations 4:00-1-1-1-1!1! k₁ 0000 0000 B₂ B₁. m₁ 0000 k3 without friction x1 (1) m2 B3 -f(t) + - X2 (1)
Learning Goal: Use the general equations of motion for plane motion to determine the initial acceleration of a spool. A spool has an outer radius R = 380 mm, an inner radius r = 210 mm, a mass m = 90 kg, and a radius of gyration KG = 320 mm. A rope is wrapped around the inner radius and pulled to the right as shown in (Figure 1). The coefficient of static friction between the spool and the ground is us = 0.2. The coefficient of kinetic friction is k = 0.15. Figure R A P 1 of 1 Part A Draw the free-body diagram for the spool, assuming the friction force acts to the right. Draw the vectors, starting at the black dots. The location and orientation of the vectors will be graded. The length of the vectors will not be graded. + 0 No elements selected Select the elements from the list and add them to the canvas setting the appropriate attributes. Submit Request Answer