In the circuit shown kp = 2 mA/V2and kn = 1.5 mA/V2 and the draincurrents are Ip1 = 3 mA and ID2 = 4mA. We give Rs1 = 1 ko, RD1 = 5ko, Rs2 = 3 ko, and (R1 // R2) =200 ko, Then the input andoutput resistances of the circuit%3D%3D%3D%3D%3Dare:R$1RinM2Rp1Rs2a.rin = 200 ka, and rout = 1.2 kob.rin = 200 kn, and rout = 191 Nwwww

By small signal analysis we will find out input and output impedance.

In the circuit shown kp = 2 mA/V2 and kn = 1.5 mA/V² and the drain currents are Ip1 = 3 mA and Ip2 = 4 mA. We give Rs1 = 1 ko, RD1 = 5 kO, Rs2 = 3 kQ, and (R1 // R2) = 200 ko, Then the input and output resistances of the circuit %3D %3D %3D %3D are: RS1 M1 M2 Rp1 Rs2 a. rin = 200 ka, and rout = 1.2 ko b. rin = 200 kn, and rout = 191 Q ww ww ww ww

In the circuit shown kp = 2 mA/V2 and kn = 1.5 mA/V² and the drain currents are Ip1 = 3 mA and Ip2 = 4 mA. We give Rs1 = 1 ko, RD1 = 5 kO, Rs2 = 3 kQ, and (R1 // R2) = 200 ko, Then the input and output resistances of the circuit %3D %3D %3D %3D are: RS1 M1 M2 Rp1 Rs2 a. rin = 200 ka, and rout = 1.2 ko b. rin = 200 kn, and rout = 191 Q ww ww ww ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question: What is the desired current? Given: (see pic)
Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. Choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5 V, the output power is 12W b. The output voltage is 2 V, the output power is 12W c. The output voltage is 12 V, the output power is 6W d. The output voltage is 0.5 V, the output power is 6W
B.. What is the load current for the circuit shown in the figure? Please choose one: a. 6.0 mA b. 3.0 mA C. 9.0 mA D. 7.5 mA
6. A bridge circuit has R, = R2 = R3 = R3 = 120.00 resistances and a 10.0 V supply. Clearly, the %3D bridge is nulled. Suppose a 3 digit DVM on a 200-mV scale will be used for the null detector. Find the resistance resolution for measurements of R4. k
*Use 4 decimal places. **Note D1 is Germanium, D2 is Silicon, For the circuit below, determine the diode voltages VD1 and VD2, diode currents ID1 and ID2, and voltage across the resistor, VRLIMIT. Use practical model. Assume r'a=150. VBIAS = 15V and RLIMIT = 1.5kohms. VD1 = Blank 1 V; VD2 = Blank 2 V; Ip1 = Blank 3 mA; Ip2 = Blank 4 mA ; VRLIMIT = Blank 5 V Capture3(1).JPG +Vo1- +VRLIMIT +VD2- Io2 VBIAS
With a D'Arsonval movement with 200 internal resistance and 100 mA FSD current, it is required to design an ammeter with a current ranges of 0.5 A, 3 A, and 5 A by using Ayrton shunt. Therefore, Rsh1 = Rhs2=............. Rh3=............
Please in typing format please ASAP for the like Please answer the same to
circiuts
For the resistor circuit shown in Figure P16, what resistance must resistor R, have to give a total resistance of 252 2? R, 16 0 22 N 75 0 180 Q
Answer a, b, c and d...
You are required to design a two types of load cells. A Cantilever beam load cell and a Hollow cylinder load cell. What equations would you use to measure strain and voltage.
Part A: A multi-range ammeter is required to measure the current in a certain network. A PMMC instrument has connected as an Ayrton shunt with a four resistor across PMMC. The resistance values are R1 = 0.006N, R2 = 0.0650, R3 = 4.00 and R4 =10.00. The PMMC has Rm = 1kQ and FSD = 50µA. %3D %3D a. Draw the circuit for the multi-range Ayrton shunt. b. Calculate the four current ranges of the ammeter. c. What is the main advantage of Ayrton shunt ammeter compared to parallel type. d. Briefly explain how this device can be calibrated. * Note: Show all calculation details. Part B: The measurement of the voltage from a prototype of a 20V DC power supply were captured by 8 times as shown in the following table: Number 1 2 3 4 6 Voltage (V) 18.5 19.8 20.2 19.9 20.0 20.1 19.7 18.9 Determine the following: 1. the arithmetic mean, 2. the standard deviation of the readings, 3. the probable error. 4. If the voltmeter that used to carry the measurements has an error of 0.5%; calculate the total…