In the circuit given in the figure, Vcc= 12 V, Vin = 10 mV, B = 100, ro= 40 kn, RB = 360 kn, RC = 3,3 kn, RE = 220, Rs = 0.5 km and RL = 42.8 kn. Accordingly, find the voltage gain (Vout/Vin) of the circuit. NOTE-1: Output impedance of the transistor will be taken into account in ro calculations... NOTE-2: Capacitors are negligible at midband frequency. vin Rs C1 RB Vcc RC NPN RE C2 CE Vout RL D

In the circuit given in the figure, Vcc= 12 V, Vin = 10 mV, B = 100, ro= 40 kn, RB = 360 kn, RC = 3,3 kn, RE = 220, Rs = 0.5 km and RL = 42.8 kn. Accordingly, find the voltage gain (Vout/Vin) of the circuit. NOTE-1: Output impedance of the transistor will be taken into account in ro calculations... NOTE-2: Capacitors are negligible at midband frequency. vin Rs C1 RB Vcc RC NPN RE C2 CE Vout RL D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the deflection factor (in V/m) of a CRO, when the deflection sensitivity of the CRO is 4 m/V.
The circuit diagram of step-up type DC-DC converter is given below. It is assumed that the output capacitor is large enough and the output voltage is constant. (Consider that there is no circuit losses.)Select an inductance value for the DCM operation state of the circuit. Assume that Output voltage (Vç) is regulated and prove that the circuit will always have to work at DCM operation statefor minimum input voltage and maximum output current.
Power electronics
answer part b,c, and d
Considerations of good circuitry design.
Correct the sentence: The aim of using coupling in multistage transistor amplifiers is to transfer DC output of one stage to the input of the next .stage and to isolate the d.c. conditions of one stage from the next stage
(b) The multistage amplifier circuit of Figure Q.2(b) have the following parameters: Qı and Q2: B= 200, VBE = 0.7 V, VT = 26 mV , VA=∞ Given that Icọ1 = 2 mA and VCEQ1 = 2 V. (i) Determine the value for R84. List the assumption/approximation made in the analysis. (ii) Sketch and label the small-signal hybrid-t equivalent circuit at midband frequency range. (iii) Calculate the small signal hybrid-n model parameters: gm and ra for Qı and Then, determine Zi2 and Zo. VSI (iv) Find +15 V TU MA RBI 100 k2 UNIVERSITI { Rc 3.3 k2 RB3 10 kN IcQI Q2 C4 Qi VCEQI Ro TEO ► 50 k2 Rs 100 2 RL V. 10k2 RE 2 kN RB4 C3 Zi2 Z, Figure Q.2(b) AYSIA
this question is analog electronics question
For the p-channel JFET circuit in the Figure, the transistor parameters are: /oss = 2 mA, Vp = |1.75| V. (a) Determine Ipo and Vspo- (b) Give the small signal model (c) Determine the small-signal voltage gains Av = vo/vi QUESTION I: For the p-channel JFET circuit in the Figure, the transistor parameters are: Ioss = 2 mA, Vp = |1.75| V. (a) Determine Ipo and Vspo- (b) Give the small signal model (c) Determine the small-signal voltage gains Av = vo/vi VDD = 10 V Rg = 5 k£2 R1 = 90 kQ %3D Cc2 RL = 10 k2 R2 = 110 k2 ww
Q3. The transistor parameters in the ac equivalent circuit shown in the figure below are ß1 = B2 = 100, VA1= VA2 =00, Vr= 0.026 v, Icoi = 0.5 mA, and Ico2 = 2 mA. (a) Find the small-signal voltage gain Avi = Vo1/Vi . (b) Determine the small-signal voltage gain Av2 = Vo2/Vo1. (c) Determine the overall small signal voltage gain A,= Vo2/Vị . RE2 C4 k2 Solution: o Vo2 Vol Q2 Rci = 4 k2
How does the external resistors Rf and Ri affect the gain of non-inverting amplifiers? Discuss briefly.