in the chamber shown, section (1) has a diameter of 4.2 in., and the flow is 2.65 ft^3/s. Section (2) has a diameter of 3.3 in., and the flow velocity (out) is 31.12 ft/s. compute the flow velocity (in ft/s) of section (3) if its diameter is 1.61 in. Hint: Check whether flow in section (3) is inflow or outflow.

in the chamber shown, section (1) has a diameter of 4.2 in., and the flow is 2.65 ft^3/s. Section (2) has a diameter of 3.3 in., and the flow velocity (out) is 31.12 ft/s. compute the flow velocity (in ft/s) of section (3) if its diameter is 1.61 in. Hint: Check whether flow in section (3) is inflow or outflow.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Asap
Q₁/Water flows in the pipe shown in Fig. No. (1) from point No. (1) to point No.(2) at flow rate of Q = 0.1414 (m³/s). If P₁ is 70 (Bar), P2 is 9.81 (Bar), f= 0.02 and length of pipe from point No. (1) to point No.(2) is 15.67 (km). (1) Find the diameter of the pipe (2) Find flow velocity in the pipe. (3) Draw the H.G.L. of flow in the pipe. Fig.(1) P2=9.81 (Bar) B 400 m Q 30° p1 = 70 (Bar) A Reference Line
Help me please
1. Pipelines 1, 2 and 3 are connected with parallel to each other with pipeline 1 having diameter of 450 mm, 600 m long, pipeline 2, having 400 mm , 800 m long and pipeline 3, 500 mm , 700 m long. The 3 pipes carries a combined discharge of 0.92 m³/s. Assuming f = 0.022 for all pipes compute the the discharge for each pipe. Q=0.92 Q₁ = 0.3228 m³/s, Q₂ = 0.2083 m³/s, Q3= 0.3889 m³/s 450 mm 600 m 400 mm 800 m 500 mm 700 m Q=0.92
Determine the head loss in feet in PIPE 1. a.2.111 b.12.4962 c.6.9210 d.8.4744 Determine the head loss in feet in PIPE 5. a.1.0379 b.4.1664 d.3.5256 d.9.2994 Determine the flow in the upper branch pipe Q2 in cubic feet per second. a.1.4880 b.1.6667 c.3.052 d.7.7964 Determine the head loss in feet in PIPE 2. a.3.1315 b.1.3427 c.3.6269 d.4.0906 Determine the total head loss in feet between the inlet A and the outlet D. a.26.2109 b.12.6597 c.6.7759 d.9.6057
Q4 In the following figure shows a channel contraction section often called a venturi flume, because measurements of y, and y2 can be used to meter the flow rate. Show that if losses are neglected and the flow is one-dimensional and subcritical, Apply this to the special case b;=3 m, b;=2 m, and y,=1.9 m. a) Find the flow rate if y2=1.5 m. b) Also find the depth y2 for which the flow becomes critical in the throat. b, b2 Top view Side view
pls answer this assignment as soon as possible
Water discharges from the Annable Tank to the Schmidt Tank as illustrated on the figure. The velocity in pipe #2 is known to be 2.25 m/s. All pipeline information is provided on the figure below. As shown on the figure, a globe valve is installed at the midpoint of Pipe #2. Neglecting all local losses with the exception of the valve loss (K = 10): i. establish the flow rate entering the Schmidt Tank ii. report the value of H shown on the figure. Annable Tank Globe Valve Kv = 10 Ans: Q = 0.271 m³/s a Pipe #2 L = 150 m D = 300 mm C = 120 V = 2.25 m/s H = 7.92 m Pipe #1 L = 200 m D = 250 mm C = 110 Pipe #3 L = 250 m D = 400 mm C = 125 ▼ Schmidt Tank H
Homework 2 Water flows at a velocity of 1.8 m/s in a 150 mm diameter pipeline as shown in figure. At a particular section, the (gouge) pressure is equal to 150 kPa, and downstream of this section, the pipe elevation Increases by 1.2 m and the water is discharged through a 50 mm nozzle. Estimate the head loss between the section where the pressure is 150 kPa and the section is just downstream of the nozzle discharge. 1.8 m/s 150 kPa. 9 Pipeline 150 mm 1.2 m Nozzle 4 50 mm
Please help with question 1 of Fluid Mechanics Hw