In the balanced three phase power measurement using two wattmeter method, each wattmeter reads 20 kW, when the pf is unity. What does each wattmeter reads when the pf falls to (i) 0.6 lag and (ii) 0.819 lag. The total three-phase power remains unchanged. (i) W1 at 0.6 lag (i) W2 at 0.6 lag (ii) W1 at 0.819 lag (ii) W2 at 0.819 lag

In the balanced three phase power measurement using two wattmeter method, each wattmeter reads 20 kW, when the pf is unity. What does each wattmeter reads when the pf falls to (i) 0.6 lag and (ii) 0.819 lag. The total three-phase power remains unchanged. (i) W1 at 0.6 lag (i) W2 at 0.6 lag (ii) W1 at 0.819 lag (ii) W2 at 0.819 lag

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The data of the power system shown in the figure: X= 1.2 p.u. X= 0.15 p.u. 20MVA G1, G2, G3: T, Т, Тз: L1, L2, L3, L4: Ls: Draw the reactance diagram marked on it all the reactance's in per-unit. 11 KV 30MVA 11/66 KV 66KV X= 400 66KV X= 202 T1 L (G1 T3 Ls L4 美 T2 G3 G2
Simple summary about the measurement of power in a 3 Phase AC circuit using a two-wattmeter. Explain the relationships between ammeter, wattmeter, and total power.
At what p.f will one of the wattmeter reading be zero in a three-phase system. Please answer this in detail
In a 3-phase power measurement by two wattmeter method, both the wattmeter's shows identical readings. The power factor of the load is Select one: O a. Unity Ob.0.8 leading O C. Zero d. 0.8 lagging
Problem #16) Given the following potion of a circuit having current values of: A IA = 500 mA, I³ = 1200 mA, Ic = 400 mA (in the directions that they are labeled), Determine the current ID as labeled using Kirchhoff's Current Law. Іву Ic/ ID ID= (mA)
In the balanced three phase power measurement using two wattmeter method, each wattmeter reads 18 kW , when the pf is unity. What does each wattmeter reads when the pf falls to (i) 0.707 lag and (ii) 0.422 lag. The total three-phase power remains unchanged. (i) W1 at 0.707 lag (i) W2 at 0.707 lag (ii) W1 at 0.422 lag (ii) W2 at 0.422 lag
In an Industry, three phase power measurement is carried out, using two wattmeter method, each wattmeter reads 14 kW , when the pf is unity. What does each wattmeter reads when the pf falls to (i) 0.6 lag and (ii) 0.819 lag. The total three-phase power remains unchanged.
In the two-wattmeter method of power measurement for a three-phase load, the readings of the wattmeter are 2000 W and 1000 W. What is the power factor of the load?
Match the following Each load wilI be connected between two phase wires Choose... Power measured by two wattmeter method Choose... Each load will be connected between a Phase wire and Neutral wire only unbalanced Load Both Balanced and Unbalanced Load Current in the neutral wire is zero Star connection Junction Point where one end of all three phase loads joined together Delta Point Delta connection Only Balanced Load Series Connection Neutral point
An alternator is connected in star. If the phase voltage is 110 V, the line voltage is *
The average power lost in the transmission line (single phase) is equal to the power produced by the source (singleFind the phase ratio in%.
Please answer all subpart either dislike is ready.. please all subpart