In the 190.0 meter span cable and a horizontal load of 5.550 KN/m horizontal load, find the location of point C from point B = ____________m the lowest point in the cable system. Then Determine the maximum tension on the cable, Tmax = _____________KN and the diameter of the cable , Cable Diameter = _______________ if the maximum allowable stress is 1250 MPa for the cable. Find also the value of T1 = _______________KN given the specifics at the figure below which is the pulley at A, Then determine the volume of concrete Vconcrete = ___________m3 of the dead man’s load at point D of the figure if the unit weight of concrete is 24 KN/m3.

Q: A uniform horizontal beam with a length of 3.00 m and a weight of 40 N is attached to a wall by a…

A:

Q: force members in the bars and state the

A: Given: A struss To determine forces in all members

Q: Determine the largest weight of the crate that can be supported. Express your answer to three…

A:

Q: Calculate the tension in each cable around the pulley.

A:

Q: 18 ft 24 ft 10 ft 6ft

A: Given that, Weight of each light, W= 65 lb, Drawing the FBD of the light, The angle θ…

Q: What would be the maximum weight W of the block, shown in the following figure, so that the tension…

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: A rigid bar AD is supported by a ball-and-socket at D, and the two cables are attached to the beam…

A:

Q: What would be the maximum weight w of the block, shown in the following figure. so that the tension…

A:

Q: 2. A steel plate structure is held by cable AB and a pin support at C. The plate has a total weight…

A: W = 700 NHole radius, d = 0.04 mIt is asked to find the reaction at C and the tension in the cable

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: A 292-lb box is held at rest on a smooth surface (9 = 15°) inclined by a force, 'P' making an angle…

A:

Q: 4. Determine the MINIMUM tension in the cable if luted load w=2000 lb/ft. The 0.59

A:

Q: Determine the components of reaction at the ball-and-socket joint AA using scalar notation.…

A:

Q: What would be the maximum weight W of the block, shown in the following figure, so that the tension…

A:

Q: Q10/ The steel Cable AB and AC are attached to the top of the transmission tower. The tension force…

A:

Q: 5. A cylinder having a mass of 250 kg is to be supported by the cord which wraps over the pipe.…

A:

Q: Cables AC and BC are attached to points A and B respectively as shown. These two cables are then…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: Determine the tension T on the cable if the boom has a weight of 500N. b)Determine the force…

A:

Q: Q1.) A cable system is subjected to three concentrated loads as shown. The sag at point Cis measured…

A: A cable system is subjected to three concentrated loads as shown. F1 =10 KNF2 = 10 KNF3 = 30 KN The…

Q: You must have to include the diagram. Don't make any mistakes while solving.

A:

Q: The figure below shows a bird feeder that weighs 184.7 N. The feeder is supported by a vertical…

A: The weight of the bird feeder, (W)=184.7 NThe angle of left string with branch, ()=60oThe angle of…

Q: What would be the maximum weight W of the block, shown in the following figure, so that the tension…

A:

Q: A cable is loaded and supported as shown in Fig. The vertical distance vc is 4 ft. Determine The…

A: Let  Ax and Ay be the normal reaction at support ADx and Dy be the normal reaction at support…

Q: Consider the antenna in (Figure 1). Figure 300 100 158 1258 100 V 1 of 1 If the tension developed in…

A:

Q: Determine the force in cable AB and support C.

A:

Q: Find the true magnitude and direction of the forces at all the supports A and B of the truss at…

A:

Q: Calculate the tension in each cable in kilo-Newtons.

A:

Q: Q10/ The steel Cable AB and AC are attached to the top of the transmission tower. The tension force…

A: Given-Data:- Tension Force in AB ( FAC)=8KN To-Find:-  FAB R

Q: A 4.2‑kg brown hare walks on a horizontal beam (the beam's mass m = 2.8 kg and length a = 2.4 m).…

A: Now according to given conditionlet T2=Tso as per given conditionT1=3TNow∑Fy=0T1+T2=W+WbHere…

Q: Question 2) Determine all member (internal) forces on the system given that P is 35 N, and c is 1000…

A:

Q: 13.) Cords are loop around a small spacer separating two cylinders each weighing 400 lb and pass, as…

A: GIVEN DATA WEIGHT OF CYLINDER W=800lb WE HAVE TO FIND ANGLE AND NORMAL PRESSURE N

Q: late the tension in the cable- r of the tank.

A: intro0duction: here we have to find out tension on cable

Q: A pole is supported by a wire which exerts a pull of 200 lb on top of the pole. If the angle between…

A: Horizontal component,FH=200Sin(50°)=153.21lb Vertical component,Fv=200Cos(50°)=128.56lb

Q: Two cables support an unknown weight. If the tension in cable BC is 100 lbs, then what is the…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.