In steam power plants, open feedwater heaters are frequently utilized to heat the feedwater by mixing it with steam bled off the turbine at some intermediate stage. Consider an open feedwater heater that operates at a pressure of 1000 kPa. Feedwater at 500C and 1000 kPa is to be heated with superheated steam at 2000C and 1000 kPa. In an ideal feedwater heater, the mixture leaves the heater as saturated liquid at the feedwater pressure. Determine the ratio of the mass flow rates of the feedwater and the superheated vapor for this case (m1/m2).

In steam power plants, open feedwater heaters are frequently utilized to heat the feedwater by mixing it with steam bled off the turbine at some intermediate stage. Consider an open feedwater heater that operates at a pressure of 1000 kPa. Feedwater at 500C and 1000 kPa is to be heated with superheated steam at 2000C and 1000 kPa. In an ideal feedwater heater, the mixture leaves the heater as saturated liquid at the feedwater pressure. Determine the ratio of the mass flow rates of the feedwater and the superheated vapor for this case (m1/m2).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gas turbine uses two compression and two expansion stages, each stage having a pressure ratio of 4. The working fluid is intercooled between the two compression stages and reheated between the two expansion stages. Air enters the gas turbine at 100kPa and 17°C. The combustion chamber and reheat stage each contribute 300kJ/kg of heat. A regenerator uses exhausted gases to increase the working fluid temperature prior to the combustion chamber by 20°C. Assume constant thermal properties of air evaluated at 300K during your solution. Assume all turbine and compressor stages are isentropic. Draw the T-s diagram based on the numbering convention in the schematic below. Determine the system's thermal efficiency. Determine the required air mass flow rate to obtain an output of 10MW. 26 REMEWS REHEAT JNTER. Ti C2 Come REGEN. Scannad wim Camirwner
A refrigerator using R-134a is located in a 20°C room. Consider an ideal cycle, but the compressor is neither adiabatic nor reversible. Saturated vapor at -20°C enters the compressor, and the R-134a exits the compressor at 1017 kPa. The mass flowrate of refrigerant around the cycle is 0.2 kg/s and the COP is measured and found to be 2.3. Draw the T-s diagram, indicating the temperature and pressure lines. Determine the temperature at the outlet of the condenser and the power input to the compressor in kW. Determine, the temperature at the exit of the compressor, if the heat that the compressor losses is 11.53 kJ/kg. Note: Perform energy balance. For this part, take 1017 kPa as 1000 kPa.
R134a enters the condenser of a residential heat pump at 850 kPa and 70°C at a rate of 0.020 kg/s and leaves at 750 kPa and 2°C. The refrigerant enters the compressor at 180 kPa and 8.0°C. Determine (a) the isentropic efficiency of the compressor (in %), (b) the rate of heat supplied to the heated room (in kW) and (c) the COP of the heat pump. Disregard any heat loss in the expansion valve and compressor as well as the change in potential and kinetic energy of the refrigerant in any part of the cycle.
During the isothermal process of a cannot cycle,the working fluid experiences an entropy change of -0.7Btu/R.If the temperature of the heat sink is 95.Determine the heat transfer in KJ
A vapor-compression cycle is used as a refrigerator to extract 8 kW of heat from a cold space at 0°C and rejects heat into a space at 25°C. R-134a enters the compressor at 140 kPa superheated by 4°C above the saturation temperature and leaves at 900 kPa. It exits the condensor as a saturated liquid. Assume that pressure losses are negligible and that the compressor is isentropic. Report your answers to four significant digits using rounding. QUESTION 1 Report the maximum possible COP. QUESTION 3 Report the power required by the compressor. QUESTION 2 Report the mass flow rate in kg/s. QUESTION 4 Report the COP for the cycle.
A high pressure steam turbine receives steam from a boiler under unknown conditions. The isentropic efficiency of the turbine is 75% and it produces 1MW. The high pressure turbine outlet steam is at 1.4 MPa under saturated conditions. The high pressure turbine exhaust supplies 1000kg/min for use in a process, in addition to an unknown flow of steam that follows the path, being supplied to a low pressure turbine that produces 820kW when it releases steam at 10kPa and has a isentropic efficiency of 60%. The steam that was used for the process (out of the high pressure turbine) after being used, returns to the cycle taken by the pump, which also takes the outlet of the condenser and does so at 10kPa as saturated liquid. Consider the efficiency of the pump equal to 90%. Determine: A) the mass flow through the boiler B) the pressure and temperature at the outlet of the boiler C) the thermal efficiency of the cycle
Compressor as the core part of a domestic air conditioner is using Refrigerant-134a as ns working fluid. The refrigerant enters the compressor at 140 kPa and –13°C with the required power input of 120 kW, and it is compressed to the condenser pressure and temperature of 1000 kPa and 60°C respectively. Evaluate if the adiabatic compressor is able to deliver compressed air at a minimum rate of 5 kg/s. Justify your answer with relevant calculations.
The 7FA gas turbine manufactured by General Electric is reported to have an efficiency of 35.9 percent in the simple-cycle mode and to produce 159 MW of net power. The pressure ratio is 14.7 and the turbine inlet temperature is 1288°C. The mass flow rate through the turbine is 1,536,000 kg/h. Taking the ambient conditions to be 20°C and 100 kPa, determine: (a) the isentropic efficiency of the turbine and the compressor, (b) the thermal efficiency of this gas turbine if a regenerator with an effectiveness of 80 percent is added. Answers: (a) 0.849, 0.924 (b) 0.496
Consider a reversible Carnot cycle with 1.75 mol of ideal gas with Cv = 3R/2 as the working substance. The initial isothermal expansion occurs at the hot reservoir temperature of Thot = 920. K from an initial volume of 4.00 L (Va) to a volume of 11.50 L (Vb). The system then undergoes an adiabatic expansion until the temperature falls to Tcold = 375 K. The system then undergoes an isothermal compression and subsequent adiabatic compression until the initial state described by Ta = 920. K and Va = 4.00L is reached. a. Calculate Vc and Vd. b. Calculate w for each step in the cycle and the total cycle. c. Calculate the efficiency, ε, and the amount of heat that is extracted from the hot reservoir to do 1.00 kJ of work in the surroundings.