In picking up a load from position B, a cable tension T of magnitude 24 kN is developed on the construction crane cable as shown.18 mA.TY30 m-y5 m6 mCompute the components of the Force VectorFAB = nxi+ nyj+ nzk(Answer in KN)FoChoose... +

Given data: The value of the cable tension is T=24 kN The vector of position B is…

Answered: In picking up a load from position B, a…

In picking up a load from position B, a cable tension T of magnitude 24 kN is developed on the construction crane cable as shown. 18 m 1. 30 m B 6 m 5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Situation 3. The system shown anchors a stanchion of a cable-suspended roof. If the tension in cable…

Q: 2. The bars 1, 2 and 3 are connected at point D, in which they are loaded by a vertical force F =…

A: Write the given data with suitable variables. F=700 Na=2.5 mb=1 mc=2 mh=5 m

Q: The 50-kg plate ABCD is supported by hinges along edge AB and by wire ED (assuming that wire CE in…

A: W=50 kgfind:The tension in the wire

Q: The uniform 18kg Bar OA is held in the position shown by a smooth pin at O, and the cable AB which…

A: The given figure can be drawn as shown below, From the figure length AE, OE and angle θ can be…

Q: 4) Determine (a) the tension in the tension rod, 'BC' and (b) the reaction (magnitude and direction)…

A: Given: The loading system is shown below:

Q: Determine the tension at AC. 2 m. 2 m. B cable -60 w =30 kN bar B.

A: Given dataWeight of the block W =30kNTo determine the tension in the cable AC

Q: Determine the tension developed in cables AB, AC, and AD 2 m 1 m 30 2 m B 600 N

Q: A 10-H boom is acted upon by the 50 - lb force shown. Determine the tension in each cable.

A: Write the position vector of point B and C, Write the unit vector from B to D.

Q: Two cables tied together at C are loaded as shown. Determine the range of values of Q for which the…

Q: Three cables are used to tie the balloon shown in Figure. Determine the magnitude of the vertical…

Q: 4. Given the frame below, determine the forces on member EBD at B and D. 2 ft •D A B 3 ft с AL 4f+…

Q: Determine the horizontal and vertical reactions at pin A on member AB. Roller E is pinned to the…

A: Given: The mass of body, m = 1500 lb

Q: The frame shown is supported by three cables and a ball-and-socket joint at A. For P = 0, determine…

A: To find: Tension in each cable The reaction at point A. Free body diagram of the frame:

Q: A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B,…

A: we solve this question by resolution of component of force in 3D ( 3 dimensions). given dimensions…

Q: A container of mass m = 120 kg is supported by three cables as shown. Draw the free-body diagram…

A: To determine the tension in each cable, take all forces on point A and draw free body diagram

Q: A 550 N cylinder 1.4 m in diameter is lodged between two cross pieces which make an angle of 110°…

Q: determine the traction

Q: Two cables are tied together at C and are loaded as shown. Part 1. If W=160 lb, determine the…

A: Free body diagram tan∝=3016 ∝=61.93°tan β=1216 β=36.87° a For equilibrium ,ΣFx=0 ; TCA…

Q: Show the detailed diagrams, calculations, and solutions. A transmission tower is held by three guy…

A: B=-20,0,25A=0,100,0 T=525 lb=2335.316348 N≈2335.316 N

Q: In the frame shown, member ACE and BCD are connected by a pin at C and by the link DE. Determine all…

Q: 2. Two cables support a 400- Ib weight as shown. Determine the tension in each cable. 400 - Ib

Q: 2m Im 1m -2m 2m 2m The crate weighs 450 kg and is supported by three cables as shown in the figure…

A: As per our guidelines we are supposed to solve 3 sub-parts if multiple sub-parts are asked. Kindly…

Q: B 45° 30° 60° E D

Q: Y pies FD Fs D X 0,6 m FA W

Q: Show the complete solution: Two cables tied together as shown in figure , Knowing that Q = 60 lbs…

A: Consider the free body diagram of the point C.

Q: Determine the forces in each cable if P = 10KN.

Q: A 10-H bom is acted upon by the 500 - lb force shown. Determine the tension in each cable. 6 ft E

Q: Determine the tension in each segment of the cable shown

A: Given: To determine: Tension in all cables

Q: Determine the forces in each cable if P = 10kN.

Q: The tension in cable AD is N.

Q: An 8-m long cantilever beam is loaded with vertical forces A = 60 kN and B = 108 kN, separated by a…

Q: 4. A cylinder weighing 400lb is held against a smooth incline by means of of a weightless rod AB.…

Q: 1. From the cable shown, determine the following: a. Tension at point 3. 15m 15m 15m 15m H b.…

A: Given: To find: Tension in cable at point 3, 2, 1

Q: is The left support of the cable shown in Fig. located 40 ft below the right support. The cable is…

A: For the given cable, Span length, l=400 ftDifference between level of both support, d=40 ftsag of…

Q: 1. The wheel loads on a jeep are given. Determine the distance x so that the reaction of the beam at…

Q: A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at B,…

Q: Determine the internal forces at point E

Q: C B 2 m 30° 3 kN 2 m A 4 kN - 2 m For the following truss system, determine the tension TAB in the…

Question

In picking up a load from position B, a cable tension T of magnitude 24 kN is developed on the construction crane cable as shown.
18 m
A.
TY
30 m
-y
5 m
6 m
Compute the components of the Force Vector
FAB = nxi+ nyj+ nzk
(Answer in KN)
Fo
Choose... +

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The rigid pole and cross-arm assembly is supported by the three cables shown. A turnbuckle at D is tightened until it induces a tension 7 in cable CD. (i) Express T as a vector (ii) Determine the magnitude TGF of the projection of T onto line GF (iii) Determine the magnitude Top of the projection of T onto line OD T = 6.2 kN a = 0.5 m 1m b = 2m c = 1m Expression of T as a vector: TCD-TUCD = ICD UCD= [TCD UCD= B 1.5 m m 0.5 m 3m 1.5 m i+ 2m E (XD-Xc\i+(VD-Yc)+(Zp-Zc) (XD-XC)+(YD-Yc²+ (zp-Zc)²] ✓ 0.00 T= 6.2 KN
Four sets of flexible cables, spaced at 120° intervals, are used to stabilize a 400-ft communications tower. The tower and one cable from each set is shown in Fig. The weight of each tower is 40 lb/ft, and the communica- tions equipment at the top weighs 2000 lb. Determine the axial forces transmitted by transverse cross sections at points A, B, C, and D of the tower. 50 ft 30 1500 lb 100 ft B 40° 1250 lb 100 ft 50° 1000 lb 100 ft 50 ft 60 750 Ib
A freight car is stopped on a track at an angle of 25o to the vertical. The gross weight of the wagon and its load is 36kN and acts at a point 750 mm from the track, in the middle between the two axles. The wagon is supported by a cable 600 mm from the track. Determine the traction on the cable and the reaction on each pair of wheels.
3
Q.2) A plate is supported by a rope and two hinges as shown in figure. Assume that hinges do not exert couples on the plate, and the hinge at A does not exert a force on the plate in the direction of the hinge axis. If the plate is uniform with 50 kg mass, determine the tension in the 240 mm 240 mm гope. 400 mín 400 mm 200 mm! 200 mm B 480 mm
The cable shown supports a girder which weighs 850 lb/ft. Determine the tension in the cable at points A, B, and C.
thx
I need the answer quickly
25.
2. Find the forces in the members DE, BD and EG. AP MM. B 10 m t C D 10 m E F 25000 N 10 m G 15 mi
3. For a frictionless pulley and cable, tensions in the cable (T₁ and T₂) are related as a. b. T₁ > T₂ c. T₁ = T₂ d. T₁ < T₂ e. T₁ = T₂ sin 8 T₂ T₁