In Hydrometer test, we commonly do a few corrections to the readings we take off the Hydrometer stem.First, discuss why we need these corrections. Second, list and discuss the common corrections we make duringa Hydrometer reading. [5 pts]

The objective of the question is to understand the necessity of corrections in the readings taken…

Answered: In Hydrometer test, we commonly do a…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer fast
1. A clean circular glass tube is to be selected in the design of a manometer to measure the pressure of Kerosene . Specific gravity of kerosene 0.82 and surface tension of kerosene = 0.025 N/m. If the capillary rise is to be limited to 1 mm, the smallest diameter (cm) of the galss tube should be most nearly ... a) 1.35 b) 1.5 c) 1.75 d) 2.00
HYDROSTATIC FORCE ON PLANE SURFACE can someone help me analyze this experiment? For fully submerged: - compare the results of W x r with the calculated values of F x (Xcp + hs). - give reasons for discrepancies. - what can you obtain from the relationship of the graph? Does the experiment confirm the results of computed values of the magnitude and location of the total hydrostatic force?
H.W.12// A vertical conduit is carrying oil (SG manometer is tapped into the conduit at points A and B. Determine the difference in pressure between A and B when h = 3 in. What is the difference in the piezometric pressure between A and B? 0.95). A differential mercury %3D SGm= 13.6 %3D 18 is =3 in Mercury
Plz write neat
Answer the following questions: 1. A clean circular glass tube is to be selected in the design of a manometer to measure the pressure of Kerosene . Specific gravity of kerosene = 0.82 and surface tension of kerosene = 0.025 N/m. If the capillary rise is to be limited to 1 mm, the smallest diameter (cm) of the galss tube should be most nearly a) 1.35 b) 1.5 c) 1.75 d) 2.00 2. Both a gage and manometer are connected to a gas tank to measure its pressure. If the reading on the pressure gage is 80 kPa. The distance between the two fluid levels of the manometer h is ..... if the gage fluid in the manometer is a mercury (s 13.6); and h is if the gage fluid in the manometer is water. a) 0.4 m; 9m b) 0.9m; 4.3 m c) 6.213m; 0.7626 m d) 4.91m; 0.668m P= 80 kPa h = ? 3. A 50-ton, 6-m diameter hemispherical dome on a level surface is filled with water as shown in figure. An engineer claims that be can left this dome by attaching a long tube to the top and filling it with water. So, the required…
Which parameters do Barometer and Manometer measure? o Pressure difference; Atmospheric pressure o Pressure difference; Absolute pressure o Absolute pressure; Pressure difference o Atmospheric pressure; Pressure difference • What is the absolute pressure at location 1 (P1)? Ga OP = Pan + Pgh OP = Pan OP, - Pgh OP can not be calculated
3.23 A tank is fitted with a manometer on the side, as shown. The liquid in the bottom of the tank and in the manometer has a specific gravity (SG) of 3.0. The depth of this bottom liquid is 20 cm. A 15 cm layer of water lies on top of the bottom liquid. Find the position of the liquid surface in the manometer. 15 cm Water Ah =? 20 cm SG = 3.0 Problem 3.23
4Q. Compute the capillary depression of mercury at 68 °F (0 = 140°) to be expected in a 0.05 in diameter tube?
I need the answer as soon as possible
The readings given below were made with a tacheometric theodolite having a multiplying constant of 100 and no additive constant. The reduced level at station A was 100.0 m and the height of the instrument axis 1.2 m above the ground. Calculate the horizontal distance from station A to station B in m. Station Bearing (0) Vertical Angle (⁰) Stadia Readings A 10 48 138 2.048; 1.56; 1.000 2.112; 1.39; 0.600 -19 Note: Variables given in Question 6, 7, 8, 9 and 10 are NOT the same. Carefully check the given data for each question. To B C
Exercise 1: For the setup shown. Plot to scale elevation head, pressure head, total head and seepage velocity versus distance along the sample axis. 10 8. +8 +5 2. Sand n0.33, k1 t/min Elevation (ft)

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

In Hydrometer test, we commonly do a few corrections to the readings we take off the Hydrometer stem. First, discuss why we need these corrections. Second, list and discuss the common corrections we make during a Hydrometer reading. [5 pts]