In figure shown, valve F is partly closed, creating a head loss of 3.6ft when the flow through the valve is 1.0cfs. What is the length (ft) of 10-in pipe connected to reservoir A? Use Hazen- William Formula, Q = A(1.318CRº6³5©5*), where S- (Hydraulic Slope) EL 150 10 C = 100 1000-12" C = 80 20' B 5000'-12" C = 120 E

In figure shown, valve F is partly closed, creating a head loss of 3.6ft when the flow through the valve is 1.0cfs. What is the length (ft) of 10-in pipe connected to reservoir A? Use Hazen- William Formula, Q = A(1.318CRº6³5©5*), where S- (Hydraulic Slope) EL 150 10 C = 100 1000-12" C = 80 20' B 5000'-12" C = 120 E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer question 3 only
Three pipes 1, 2 and 3 from three reservoirs A,B and C, respectively, meet at a junction whose elvation is 366 m. Water levels at reservoir A and B are elevations 825 m and 716 m respectively. Useful properties of the pipe are given: for pipe 1, L- 300 m diameter+ 200mm f= 0.018; for pipe 2, L= 1200 diameter = 300 mm, f=0.020 and for pipe 3, L = 1500 m diameter= 0.025. If the pressure at the jucntion of the pipe is 2730 kPa, find the elevation of water at reservoir C. a. 462.07 m. b. 480.33 m. C.544.96 m. d. 503.29 m.
Q2) For the pipe system shown in the figure, the flow rate is 0.00085 m³/s & v-1.14*106 m²/s, F-0.023, p=990 Kg/m³, diameter 15mm, Celbow=0.9, Cvalve -10, Cfaucet -2.Calculate the pressure at point (1)? -3.0- Faucet 4.5- -1.5- 3.0 Valve EXE 3.0 elbow 005
For the 4-reservoir shown, if elev. P' = 86.95m, find the discharge at the 150mm diameter pipe. Assume f=0.02 for all pipes. El. 50m El. 90m 450 m - 200 mm 600 600 m mm P El. 75m 300 m - 200 mm 900 m 150 mm El. 30m Vl
For the piping system shown below, determine the flow distribution and the piezometric heads at the junction (j) using the Hardy-Cross Method of solution. Power = 20 Kw D= 0.2 m, D,= 0.15 m, D= 0.15 m f,= 0.021, f= 0.018, f, = 0.023 L2=180 30 m L3=385 B L1=135 2 15 m | 10 m A 3 Pump 1
The flow rate for the pipe system is 0.050 m³/s with a total head loss of 12 m. Use C = 120 for all pipes. 2 3 Pipe Length Diameter 1 400 m 200 mm 2 500 m 180 mm 300 m 4 620 m 250 mm a. Calculate the head loss in pipe 2.2.81 m b. Solve the rate of flow in pipeline 3. 0.0278 m³/s c. Compute the diameter of pipe 3. 176.54 mm Situation: 3
If the total flow of 4.0m3/? takes place in the three pipes. Determine the distribution offlow. The pipe lengths, diameters and frictions factors are shown below.
Q=9 P=29 Pls hand written solution
The three water-filled tanks shown in the figure below are connected by pipes as indicated. If minor losses are neglected, determine the flow rate in each pipe (+ is out and-is into the reservoir) Assume ha - 20 m, he-50m.hc-0m., = 400 m, ₂= 250 m, and 3 = 500 m. QA- QB Qc- Elevation - h D-0.08 m 7,-0.020 Elevation- V B D-0.10m -0.015 D-0.08 m -0.020 Elevation - he C
Q2: A is 4500 m length-gas flow line, and B is 2000 m length-liquid flow line (0.1 m diameter) both are connected with left side of 2500 m in length C-pipeline (0.15 m). If the pressure at A-pipeline inlet = 2400 kPa, pressure at C-pipeline out let = 2000 kPa, liquid flow rate = 0.009 m³/s, Gas Oil Ratio = 40 m³/m², PL 680 kg/m³, p=0.922 kg/m³, gas flowing temperature-300 K, base temperature-288 K, base pressure 101.3 kPa, Z-0.9, gas gravity 9.4x10-3 Pa.s, calculate the 0.6, gas viscosity-0.015x10³ Pa.s, and liquid viscosity diameter of gas pipeline and inlet pressure of liquid pipeline? Assume all pipes are flat and horizontal. =
f₁= = 0.0288 A 12 = 0.0260 Three pipes are in parallel with the total loss of 19.7 m. Compute the flow rate Q (m³/hr), neglecting minor losses. (p = 1000, 9 = 1.02x10-6m²/s) ma Pipe 1 2 3 L(m) 120 180 60 D₁-8 cm = 0.0314 D₁-6 cm D₂-4 cm D(cm) 8 6 4 B & (mm) 0.2 0.1 0.15
Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipediameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.