In Fig. P6.110 the pipe entrance is sharp-edged. If the flow rate is 0.004 m3/s, what power, in W, is extracted by the turbine? For water at 20°C, take p = 998 kg/m3 and μ = 0.001 kg/m-s. For cast iron, &≈ 0.26 mm. The minor loss coefficients are: Entrance: K= 0.5; open globe valve: K= 6.9 Water 40 e Turbine Casin L=125 m, D=5 cm Fig. P6.110 Open globe valve

In Fig. P6.110 the pipe entrance is sharp-edged. If the flow rate is 0.004 m3/s, what power, in W, is extracted by the turbine? For water at 20°C, take p = 998 kg/m3 and μ = 0.001 kg/m-s. For cast iron, &≈ 0.26 mm. The minor loss coefficients are: Entrance: K= 0.5; open globe valve: K= 6.9 Water 40 e Turbine Casin L=125 m, D=5 cm Fig. P6.110 Open globe valve

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows steadily downward through the pipe shown in the figure below. Viscous effects are negligible, and the pressure gage indicates the pressure is zero at point (1). Determine (a) the flowrate and (b) the pressure at point (2). (a) Q = (b) p2 = 2.1ft 3.1ft ↓s -0.12 ft (1) 5 -0.1 ft -free jet ft³/s lb/ft²
The impeller of the centrifugal pump is 350 mm diameter, and the width of the blade passages at outlet is 18 mm. A pump, which runs at 16.6 rev/s, is mounted so that its centre is 2.4 m above the water level in the suction sump. It delivers water to a point 19 m above its centre; the friction loss in the suction pipe is 68 Q² meter and that in the delivery pipe is 650 Q² meter where Q in m3/s is the rate of flow. The blades themselves occupy 5% of the circumference and are backward facing at 35° to the tangent. At inlet, the flow is radial and the radial component of velocity remains unchanged through the impeller. Assuming that 50% of the velocity head of the water leaving the impeller is converted to pressure head in the volute, and that friction and shock losses in the pump, the velocity heads in the suction and delivery pipes are negligible, calculate the following: A) The flow rate, m3/s, of the pump. B) Manometric efficiency, in %, of the pump. 0.0284 55.2 0.0397 95.5 0.0778 66.2…
During a flow of 450 L/s, a pressure of 65 kPa was measured at point C in 320 mm diameter horizontal the supply line of water turbine and a -47 kPa pressure T. was measured at point D, 2 m below point C at the 460 diameter exit pipe. mm Compute the total head extracted by a. the turbine. b. Compute the power supplied to the turbine in horsepower.
1. Water flows through a horizontal, 0.5-m-diameter pipe at a rate of 0.9 m³/s (Figure below). It is ejected from the pipe through a 0.25-m-diameter nozzle. Determine the force (F) that holds the nozzle in place if the water pressure in the pipe just upstream of the nozzle is 283 kN/m² (kPa). F Fpl V₁. in F H Vout 2. Given H= 1.8 m & D = 0.2 m through the hole in the open top container. Determine the head losses through the tank outlet if the exit discharge were 0.163 m³/sec.
%TE l, UPUOM A 9;Y) 团 / د امتحان مد1.docx The pipe assembly is subjected to the force of F = {600i + 800j – 500k} N Determine the moment of this force about point B. 0.5 m 0.4 m 0.3 m 0.3 m II
Еxample (8) Steel tube shaft having length 3mm and diameter 50mm subjected to axial compressive force 55 k N and change in temperature ( 100 °c drop). Find the change in length and diameter due to compound effect. Note: - E=200 GPa , µ=0.3, a =11.5 Mm / m°c
Solution plz
- Probl Water flows from a large open tank, through a valve and out a pipe to atmosphere. A-9 cm². Az = 11m. h₁ = 5V²/2g Find: I Discharge (Q=?) in pipe. Assumptions: a = 1.
Time: 60 Q1: pump puts 2kw in to the system. Find: b. The pressure in the pipe on section side of the pump (at C). a. Discharge. C 5 kPa L = 200 m 10m ↓ Air Water 55 marks 15 m P L = 50m D = 6 cm f = 0.025 D = 8 cm f = 0.030
Urgent
Q1: Derie an epressin for the shear stress at the pipe wall when an incompressible faid flows draugh a pipe wnder pressure. Use dinmsional ana)sis witk the following siguißcant parameters: pipe diameter D, flow velociy V, and vicenity and density p of the fuid. Q2: : Use dinensional analysis to derive as epression for the power develaped by an engine in terms of the torque T and rotartive speed u.
Problem 2: A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radial at the inlet of the rotor. The pump has the following characteristics: Flow rate Inlet diameter Outlet diameter Head Width at the inlet Width at the outlet Leakage Mechanical loss Blade angle at the outlet The water density Atmospheric pressure |Q=72 L/s DI = 90 mm D2 = 280 mm H= 25m bl -20 mm b2 = 18 mm q =2 L/s Pm = 1.41 kW B2 = 35 p = 998 kg/m³ 101 kPa