In an experiment to determine the content of acetylsalicylic acid in anaspirin tablet, the result showed that the calculated mass of acetylsalicylicacid was much higher than the indicated amount in the packaging.Identify two among the following situations that can most likely be thecause. (You can use the formula shown as guide).amount of baseamount of unreacted base/addedamount titratedmass analyte = (Vbase x Mpase) -(Vacid X Macid Xmole basemole analytex molar massanalytemole acid.mole base=amount of base that reactedThe unreacted base was overtitrated during back titration.After grinding, some of the pulverized tablet was not transferred to the flask.The mass of the tablet recorded included that of the packaging.The tablet contained other acids that can be neutralized by the base.A mole ratio of 1:1 (acetylsalicylic acid:NaOH) was used instead of 1:2.The aspirin was not completely hydrolyzed.The molar mass of salicylic acid was used instead of acetylsalicylic acid in thecalculations.

In an experiment to determine the content of acetylsalicylic acid in an aspirin tablet, the result showed that the calculated mass of acetylsalicylic acid was much higher than the indicated amount in the packaging. Identify two among the following situations that can most likely be the cause. (You can use the formula shown as guide). amount of base amount of unreacted base/ added amount titrated mass analyte = (Vbase x Mpase) – (Vacia X Macia x mole base mole acid mole analyte x molar massanalyte mole base =amount of base that reacted The unreacted base was overtitrated during back titration. After grinding, some of the pulverized tablet was not transferred to the flask. The mass of the tablet recorded included that of the packaging. The tablet contained other acids that can be neutralized by the base. A mole ratio of 1:1 (acetylsalicylic acid:NaOH) was used instead of 1:2. The aspirin was not completely hydrolyzed. The molar mass of salicylic acid was used instead of acetylsalicylic acid in the calculations.

In an experiment to determine the content of acetylsalicylic acid in an aspirin tablet, the result showed that the calculated mass of acetylsalicylic acid was much higher than the indicated amount in the packaging. Identify two among the following situations that can most likely be the cause. (You can use the formula shown as guide). amount of base amount of unreacted base/ added amount titrated mass analyte = (Vbase x Mpase) – (Vacia X Macia x mole base mole acid mole analyte x molar massanalyte mole base =amount of base that reacted The unreacted base was overtitrated during back titration. After grinding, some of the pulverized tablet was not transferred to the flask. The mass of the tablet recorded included that of the packaging. The tablet contained other acids that can be neutralized by the base. A mole ratio of 1:1 (acetylsalicylic acid:NaOH) was used instead of 1:2. The aspirin was not completely hydrolyzed. The molar mass of salicylic acid was used instead of acetylsalicylic acid in the calculations.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Consider the titration of 25.00 mL of Sprite with 0.053 M NaOH. Using the following data, determine the citric acid concentration in Sprite (g/L). Take the molar mass of citric acid to be 192.124 g/mol. Give your answer to one decimal place. initial volume (mL) final volume (mL) Your Answer: Answer Buret reading (mL) 1.64 14.52
A 0.5504-g sample of KHP (potassium hydrogen phthalate, KHC8H4O4; molar mass = 204.22 g/mol) is completely dissolved in enough deionized water to make 50.00 mL of solution. The titration of this solution with a KOH solution requires 20.50 mL of the base (KOH solution) to reach the “end-point”. What is the molar concentration of KOH solution? The reaction occurs as follows: KOH(aq) + KHC8H4O4(aq) --> K2C8H4O4(aq) + H2O(l) (A) 0.2457 M (B) 0.1315 M (C) 0.05390 M (D) 0.03823 M
A student is given 0.716 g of an unknown acid, which can be either oxalic acid, H2C2O4, or citric acid, H3C6H5O7. To determine which acid she has, she titrates the unknown acid with 0.430 M NaOH. The equivalence point is reached when 37.0 mL are added. Answer the following questions to determine the identity of the unknown acid. -How many moles of NaOH are consumed? Moles of NaOH = ____ mol -How many moles of H+ acid are available to react if the acid is H2C2O4? 0.0403 mol NaOH Moles of H+ from H2C2O4 = ___ mol -How many moles of H+ are available to react if the acid is H3C6H5O7? 0.0403 mol NaOH 0.0573 mol H+ from H2C2O4 Moles of H+ from H3C6H5O7 = ___ mol
You are performing an experiment in lab that involves the titration of 25.0 mL of H2SO4 solution. You titrate the acidic solution with 0.8067 M NaOH and the equivalence point is reached by the addition of 17.31 mL of NaOH solution. Using the balanced equation below, calculate the molartity of H2SO4 in the flask. Do NOT include units. 2NaOH(aq) + H2SO4(aq) --> 2H2O(l) + Na2SO4(aq)
Hi, I need to create a formula utilizing the tols that are at the bottom of the picture. In order to find the molarity of potassium ions in a 0.122 M K₂CrO4 solution. That's an "attempt" but the software marks it wrong. Thx!
In your kitchen, you have a vinegar bottle that indicates that it has 5% vinegar. As you wanted to see if this claim is true. You decided to do a quantitative analysis u Let's assume that you are performing an experiment in a laboratory and have all for this titration. You have collected following information. Volume of the acetic acid (CH3COOH)use for the titration = 25.0 mL Morlarity of the NaOH solution = 0.90 M Initial burette reading = 22.82 mL Final burette reading = 45.67 ml Assume density of the vinegar solution is same as the density of water (1.0g/mL) Using above information how do you prove or discard above claim (5% vinegar).
How many milliliters of 0.129 M H₂SO4 are needed to neutralize 0.180 g of NaOH? Express the volume in milliliters to three significant digits. V = M= VE ΑΣΦ V = If 56.8 mL of BaCl₂ solution is needed to precipitate all the sulfate ion in a 742 mg sample of Na₂SO4, what is the molarity of the solution? Express the molarity to three significant digits. 1951 ΑΣΦ ? M ? wwww. ? How many milliliters of 0.105 M HCl are needed to completely neutralize 50.0 mL of 0.108 M Ba(OH)2 solution? Express the volume in mil ters to three significant digits. LIVE ΑΣΦ mL mL
Calculate the molarity of an NaOH solution from the following titration data. Be sure the answer has the correct amount of significant figures. The chemical equation for this titration is as follows: NaOH + KHP → NaKP + H₂O NaOH buret reading, inital: 15.27 mL NaOH buret reading, final: 8.32 mL Mass of KHP (204.22 g/mol): 1.1592 g
Calculate the molarity of an NaOH solution from the following titration data. Be sure the answer has the correct amount of significant figures. The chemical equation for this titration is as follows: NaOH + KHP ⟶ NaKP + H2O NaOH buret reading, inital: 15.27 mL NaOH buret reading, final: 8.32 mL Mass of KHP (204.22 g/mol): 1.1592 g Calculate the molarity of an NaOH solution from the following titration data. Be sure the answer has the correct amount of significant figures. The chemical equation for this titration is as follows: NaOH + KHP ⟶ NaKP + H2O NaOH buret reading, inital: 15.27 mL NaOH buret reading, final: 8.32 mL Mass of KHP (204.22 g/mol): 1.1592 g
Solution X 100 mL of 0.10 M NaOH(aq) is mixed with 100 mL of 0.10 M HBr(aq) Solution Y 100 mL of 0.10 M NaBr(aq) is mixed with 100 mL of 0.10 M HBr(aq) Solution Z 100 mL of 0.10 M HC,H,O,(aq) is mixed with 100 mL of 0.10 M NaC,H3O,(aq) 6. A student prepares three solutions, X, Y, and Z, as described in the table above. The values of Ka for the acidic species in the solutions are given in the table below. Species Ka HBr(aq) >>I (very large) HC,H;O,(aq) 1.8 x 10-5 a. Using the information above, write the letters of the solutions in the boxes below to rank the solutions in order of increasing pH. Explain your reasoning for the ranking Lowest pH Highest pH b. Does the pH of solution Y increase, decrease, or remain the same when 100 mL of water is added? Justify your answer. c. The student adds 0.0010 mol of NaOH(s) to solution Y, and adds 0.0010 mol of NaOH(s) to solution Z. Assume that the volume of each solution does not change when the NaOH(s) is added. The pH of solution Y changes…
Virtual graduate student Sherry Molestonecraft is assigned to help you carry out the standardization of your NaOH solution. She weighs out 1.30 grams of solid KHP (molar mass 204.2 g/mol) and dissolves it in about 50 mL of water in an Erlenmeyer flask. She then titrates the KHP solution to the equivalence point using the NaOH solution described in Question 1 above. The volume of NaOH solution needed to reach the equivalence point is 34.41 milliliters. This is a practice question that i need help with. thank you
Please help me with this question. Answer with full detailed step by step solutions, no cursive handwriting. Show all your work! Thanks! Copper (II) sulfate reacts with sodium hydroxide in a double displacement reaction. The equation for the reaction is : CuSO4(aq). + 2NaOH(aq)--> Cu(OH)2(aq). + Na2SO4(aq). 50.0 mL of 0.300 mol/L copper(II) sulfate is mixed with an equal volume of 0.600 mol/L sodium hydroxide. The initial temperature of both solutions is 21.4 C. After mixing the solutions in the calorimeter, the highest temperature that is reached is 24.6 C. Determine the enthalpy change of the reaction in KJ/mol of copper (II) sulphate. Then write the thermochemical equation.