In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of P= 30 kN. It is given that v = 0.35 and E= 70 GPa. 20-mm diameter 150 mm P' Determine the change in diameter of the rod. (Round the final answer to six decimal places.) The change in diameter of the rod is 0.009207 * mm.

In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of P= 30 kN. It is given that v = 0.35 and E= 70 GPa. 20-mm diameter 150 mm P' Determine the change in diameter of the rod. (Round the final answer to six decimal places.) The change in diameter of the rod is 0.009207 * mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Consider steel B is a cylindrical sample with original length 40mm and subjected to 15700N.…

A: Option b is correct.

Q: Maximum shear stress theorem, determine the factor of safety at point H,

A: Given: Yield stress=200 MPa To determine: FOS according to maximum shear stress theory

Q: At a temperature of 22.8 °C a 0.44-mm gap exists between the ends of the rods shown. At a later time…

Q: Question 2 The value of the shear modulus is about O 40% O 60% 80% 90% of the value of the Young's…

Q: Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A…

Q: The lap joint is fastened with four 0.52-in-diameter rivets. The working stress is 19.7 ksi for the…

A: Given Data The diameter of the rivet is: d=0.52 in The working stress is: σw=19.7 ksi=19700 psi The…

Q: (2a.) A metal has a flexural stress of 564 Pa. The W is measured to be 1 meter, while the load was…

A: (a) Write the formula for flexural stress in a rectangular section in a three-point test. σf=6FLwt2…

Q: Q1. The information from Young Modulus I. Stress II. Strain III. Compression IV. Stiffness А. I B. I…

A: Modulus of elasticity or young modulus is the property of a material and it also can be defined as…

Q: At a temperature of 38.2 °C a 0.49-mm gap exists between the ends of the rods shown. At a later time…

A: Given that , Aal=2000mm2Eal=75GPaαal=23×10-6/°C Ast=800mm2Est=190GPaαst=17.3×10-6/°C At…

Q: The lap joint is fastened with four 0.87-in.-diameter rivets. The working stress is 12.34 ksi for…

Q: A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free…

Q: The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the…

A: Given ,A alluminium specimen in which guage length = 50 mm and diameter of 12.5 mmLoad applied = 45…

Q: Q2/ Determine the diameter of the rivets and the forces in all rivets. Take Tallowable as 60 MN/mm2.

Q: The lap joint is fastened with four 0.75-in.-diameter rivets. The working stress is 18.86 ksi for…

Q: If a 12-ft long portion of the bar in Question 23 is elongated 0.064 in. by the pull, the unit…

Q: The data illustrated below have been determined while the tension test of the stainless steel sample…

A: Gage length of the sample, L=2.0 in Original diameter of the sample, d=0.505 in

Q: a) The stress in the wire. Answer in MPa b) The strain in the wire. c) The increase in the length of…

Q: Determine the magnitude of the force (lb) in member BD of the truss shown if P = 32693 lb, Q = 35423…

Q: The axial load 296 kN applied to the lap joint is distributed equally among the three…

Q: In a Torsion test done, the following data were collected: the radius of the specimen was 3mm and…

A: Given , d= 6 mm l = 76.2 mm

Q: Determine the magnitude of force (kN) in member AB if F=76532 N , a=2.93m , b=1.42m and c=4.16m.…

A: Draw a diagram for the problem. Here, θ and α are angles as shown in the diagram.

Q: At a temperature of 28.75 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time…

Q: A cylindrical specimen of a steel alloy having a diameter of 12.8 mm and a gauge length of 50.8 mm…

Q: A water tank made from a steel having a thickness of 12mm has the following dimensions. Internal…

Q: A bar of metal 25 mm in diameter is tested on a length of 250 mm in tension. The following results…

Q: The lap joint is fastened with four 0.65-in.-diameter rivets. The working stress is 20.72 ksi for…

Q: A rubber block is placed between two rigid walls where a load of P = 65 kN is applied on top as…

Q: Do not round intermediate answers. Give your final answer(s) to three decimal places. Check your…

Q: What is the maximum strength steel B can withstand before failure?

Q: Determine the magnitude of force (kN) in member AB if F=67139 N , a=3.46m , b=0.91m and c=5.51m.…

Q: Given; A = 500 mm2, Load 1 = 25 kN, Load 2 = 50 kN. Solve the stress in Part BC. (Write answer in 2…

Q: 5. A cylinder having a mass of 250 kg is to be supported by the cord which wraps over the pipe.…

Q: Determine the magnitude of force (kN) in member BC if F=66188 N , a=2.75m , b=1.15m and c=4.11m.…

Q: Determine the force in each member of the space truss given F-3 kN. Use positive to indicate tension…

A: Ans Given Now the coordinates of various point areNow calculate the unit vector along AD asAgain…

Q: In a tensile test for an aluminum alloy, the sample is 2 inches long and 0.5 inches in diameter. The…

Q: Need help asap Find the force (N) in link if θ= 0° and P = 295 N. Round off only on the final…

Q: Two steel wires AD and CD together with a copper wire BD is subjected to a force load as shown in…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

In a standard tensile test, an aluminum rod of 20-mm
diameter is subjected to a tension force of P= 30 kN. It
is given that v = 0.35 and E= 70 GPa.
20-mm diameter
150 mm
P'
Determine the change in diameter of the rod. (Round the final answer to
six decimal places.)
The change in diameter of the rod is - 0.009207
mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tensile stress is to be applied along the long axis of a cylindrical copper rod that has a diameter of 8 mm. Determine the magnitude of the load required to produce a 0.006 mm change in diameter if the deformation is entirely elastic. Answer in N. Round your answer to 0 decimal places.
A 76-kN centric load must be supported by an aluminum column as shown. Using the aluminum alloy 6061-T6, determine the minimum dimension b that can be used. (Round the final answer to two decimal places.) The minimum dimension b that can be used is mm.
In tensile test a plain carbon steel specimen has a (40mm) gauge length and the Final area (A final) of specimen after tensile test was 264.327. The load which caused fracture was (122.5 KN). After fracture, the final length was 47.516mm Choose the correct answers for the following sentences: Initial area (A final) of specimen * O568.254 O 313.994 325.256 152.368
Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Figure σ (ksi) 0 33.2 45.5 49.4 51.5 53.4 € (in./in.) 0 0.0006 0.0010 0.0014 0.0018 0.0022 1 of 1 Part B Determine the modulus of elasticity. E = ksi Submit Part C Determine the modulus of resilience. Ur= in-lb in³ Submit Request Answer Provide Feedback Request Answer
in a Torsion test done. the following data were collected: the radius of the specimen was 3mm and the gauge length was 76.2mm. During the elastic zone: T1=0. 01N.m. 81=14.760, 12-17.13N.m, and 02 36.910, The modulus of rigidity G will be equal to: Select one O a 44.283 GPa. O b. 26.522 GPa. O C 462.91 MPa. O d. 12.94 GPa.
The topic is all about the different kinds of stresses the simple stress, simple normal stress, simple shearing stress. Also, show the conversion in the solution. Please use and paper to solve and use 3 decimal places. Provide also a step-by-step solution to be able to understand Thank you.
I need the answer as soon as possible
How do you dervive Hooke's law for the stress and strain components? This question pretains to the error in a measurement due to strain when using a long tape measure and that error is L-L0 . Where the error is introduced in inches into the measurement at a L length if the tape is pulled with P N (force) attached contains the question.
In a Torsion test done, the following data were collected: the radius of the specimen was 3mm and the gauge length 76.2mm. During the elastic zone: T1-0. 01N.m. 01-14.760, T2-17. 13N.m, and 02-36.910. The modulus of rigidity be equal to:
Solve all part otherwise please skip it and don't report please
27/. a) The length and area of an aluminum rod are 63.99 cm and 1580 mm2 respectively. The rod is subjected to a stress of 252.25 N/mm2. Take the modulus of elasticity as 1860 MPa. Determine (i) load and strain in the circular rod (ii) diameter of the rod (iii) how much the rod is stretched. (2 Marks)
I’m struggling with questions q1 2 3 4 5